The JA-150TP Wireless indoor thermostat
The JA-150TP Wireless indoor thermostat
2 / 3
MMX53105
Switching to the economical temperature when the system
is set:
The thermostat in the
Program
mode can react
to setting / unsetting the section, to which it is assigned. When
the section is set, it switches at once to the
Economical temperature
(if the thermostat has already heated to the
Economical temperature,
nothing changes). The thermostat still follows a pre-set timed heating
plan and the PG output switches on when it goes from the
Economical
to
Comfort temperature
even if the section is already set.
So the heating can be activated earlier than when the users come back
home and unset the system. It is valid for a fully and partially set
sections. All settings can be performed in the MyCOMPANY.
Installation
The product can only be used in an indoor environment. Install the
thermostat 1.5 m above the floor in a place where there is good natural
air circulation. Don´t install the thermostat where the measuring
can be influenced by drafts, sunlight, heaters or any other undesirable
effects.
Figure 4: 13 – Battery holders; 14 – production code;
Installation procedure:
1. Release the front thermostat housing by pressing the tab (2),
by screwdriver for instance.
2. Install the rear part of the thermostat at the chosen place (tab facing
down).
3. Follow the control panel installation manual. Basic procedure:
a.
There must be a JA-11xR radio module installed in the system.
b.
Go to the
F-Link
software, select the required position
in the
Devices
tab window and launch enrollment mode
by clicking on
Enroll
option.
c.
When you insert both batteries into the battery holder (13)
it sends an enrollment signal and the thermostat is thus enrolled
to the required position. When the enrollment procedure is done
successfully (proper communication) the exclamation symbol (3)
disappears from the thermostat’s LCD display.
4.
Put back the front thermostat part and close it.
5.
Using F-Link SW and the option Internal setting at the required
thermostat select the PG output which will be controlled and other
system settings. See more details in the chapter: Setting
the thermostat properties.
6.
Other settings can be done in the MyCOMPANY. If the system has
not been registered yet, it must be registered first (if needed ask
your authorised distributor for help). When the system is registered
already and only the thermostat has been added, then leave
the service mode to upload new system configuration
to MyJABLOTRON (ussually within 15 minutes).
7.
When registration is finished, pre-set the thermostat via
the MyCOMPANY
application, see the chapter
Setting
the thermostat properties in MyCOMPANY.
Notes:
The thermostat can also be enrolled to the system by entering
its production code (14) in the F-Link software. All digits
of the production code are required. (Example: 1400-00-0000-
0001).
Setting the thermostat properties in the
F-Link software
Basic settings can be done in the F-Link SW in the internal settings
of the specific thermostat. Where the following parameters can be set:
Controls PG:
(*No) Select which PG output will be controlled
by the thermostat. The reaction of the PG has to be set to ON / OFF
and must not be inverted. Thermostat can control only one PG output.
Reaction to high temperature:
(*None) The selection of the offered
options determines the reaction when a
high temperature
is reached.
Fire alarm, Fire instant, Report A, Report B, Report C, Report D,
Overheating or None.
Reaction to low temperature:
(*None) The selection of the offered
options determines the reaction when a
low temperature
is reached.
Report A, Report B, Report C, Report D, Freezing or None.
High temperature:
(*60 ºC) The temperature can be set in the range
of -9.9 °C to +70 ºC. When a pre-set temperature is exceeded,
the selected reaction is triggered. The value of the high temperature
always has to be higher than the low temperature.
Low temperature:
(*3 ºC) The temperature can be set in the range
of -10 °C to +70 ºC. When the pre-set temperature is undershot,
the selected reaction is triggered.
Setting the thermostat properties
in MyCOMPANY
For the settings of all thermostat parameters it is necessary to have
the Jablotron 100 system registered – see the
Installation
chapter to get
the details. A service technician pre-sets the thermostat
in the MyCOMPANY. (it is supported web and mobile applications).
In the MyCOMPANY, open
Installation management
. At the
selected system on the
Devices
tab select the cogwheel symbol
at the required thermostat position. The setting window with following
parameters is open:
Highest and lowest temperature configurable by the user
(-10 ºC
to +40 ºC).
Comfort and Economical temperatures:
are pre-settable by
the user in the range of the
lowest temperature limit
to the
highest
temperature limit.
Heating plan:
can be the same for the whole week, different for week
days and the weekend or individual for every day. Using the
button
add individual intervals when the thermostat should heat to the
Comfort
temperature
. If an interval should be erased, click on it and when the
symbol appears, by clicking on it the selected interval can be erased.
Activate economical temperature when:
None / Partially set / fully
set section to which the thermostat has been assigned.
Temperature in Standby mode:
(from -10 ºC to +15 ºC) this
determines the temperature which is going to be maintained in Standby
mode or when
Blocking
is activated.
High temperature
(from -9.9 ºC to +70 ºC), see the chapter called
Setting the thermostat properties in the F-Link software.
Low temperature
(from -10 ºC to +70 ºC), see the chapter called
Setting the thermostat properties in the F-Link software.
Hysteresis
(from 0 °C to 5 ºC) For example, if the hysteresis is set
to 1 °C and the required temperature is 30 °C, then, the PG output
is switched on when the temperature drops below 29 °C and the PG
output is switched off when it exceeds 30 °C.
Temperature correction:
(from -12.8 ºC to +12.7 ºC) This option can
fix any possible thermostat measurement deviation from the real
temperature in the premises.
MyJABLOTRON
In the MyJABLOTRON thermostats are shown at
Thermostats
and thermometers
, where all the measured values of all thermostats
and thermometers enrolled to the system are saved. This data is stored
and available for future use. Reading the temperatures is done
automatically at a 5 minute interval.
For every thermostat:
The current status is displayed (Name, Heating / Temperature
reached, Current temperature, Required temperature, Mode, Graph
of measured temperature)
The temperature can be temporarily changed
The operation mode can be changed (Program, Manual, Standby)
Temperatures are shown in a graph in the selected time period
and can be exported in various formats for future processing.
The user has authorization to edit some settings directly
in the MyJABLOTRON application. Select
Settings
Æ
Thermostats
to open
settings window with following parameters:
Basic settings:
Comfort and Economical temperatures
Heating plan
Advanced settings:
Temperature in Standby mode
Hysteresis
(0 - 5 ºC)
Temperature correction
