manualshive.com logo in svg

Jabiru j160, Руководство по эксплуатации продукта

Поделиться
Скачать
Jabiru j160 Скачать руководство пользователя страница 24

I A P   2 0 2 0 . 0 0 1 - A F M   /  

J A B I R U   J 1 6 0 / J 1 7 0

                 

  P a g e

 | 

24 

 

FOR SIMULATION USE ONLY 

 

head to the tanks. This system ensures that the air space pressure in each 
tank is the same, minimising uneven fuel feed rates. 

The J160/J170 may use either two fuel sight gauges (one in each wing root) or 
two electric fuel gauges on the instrument panel to show fluid levels in each 
wing tank. The sump tank does not have a fuel gauge as its contents are 
deemed to be unusable and should not to be considered for flight planning. 
As an option, a low level warning light may be installed in the header tank. 

NOTE 

•

 

As ground & flight attitudes are essentially the same, fuel gauge 
indications are valid in both cases 

NOTE 

•

 

Flying “1 ball” out of balance causes the fuel in the tanks to slosh in to 
one side by an angle of about 8°. This leads to uneven fuel feeding – 1 
tank emptying before the other. In extreme cases, this can cause fuel 
starvation & engine stoppage while there is significant fuel remaining in 
one wing tank. Care must be taken to fly the aircraft in balance at all 
times. 

CAUTION 

•

 

In the unusual condition where the pilot suspects that one wing tank is 
feeding and the other wing tank is not, the pilot must consider the fuel 
in the non-feeding tank as “unusable” and manage the flight 
accordingly. 

 

BRAKE SYSTEM 

The aircraft has a single disc, hydraulically actuated brake on each main 
undercarriage wheel.  

Each brake is connected by a hydraulic line to a master cylinder fitted to the 
front of the centre console in the cabin. The wheel brakes operate 
simultaneously.  

 

 

Содержание j160




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды