Jabiru 3300 Скачать руководство пользователя страница 54

Страница: 54 / 103

Page No: 54

Issue No: 1

Date: 031100

Issued By: PJA

Jabiru 3300 Component Inspection and Assembly

7.4.6

Sub-Assembly F - Gear Case

Remove distributor shaft seals and rotor seal and discard.

Inspect Distributor shaft posts for signs of leaking.

Note: If there is no signs of leaking don't disassemble. But if it is leaking

disassemble and clean off old master gasket. Inspect surfaces and

reassemble.

Clean gear case distributor shaft and engine mount plate.

Measure distributor shafts and record on build sheet.

Measure distributor shaft posts and record in build sheet.

Fit shafts into gearcase and using a straight edge and feeler gauge measure end
float. Record in build sheet.

Visually inspect gears for wear.

Fit seals to gear case.

Lube shafts and fit to gear case.

F10 Fit

rotors.

F11

Visually inspect engine mount plate for

1) Damaged Threads

2) Wear from distributor shafts.

F12

Seal up and store for final assembly.

Содержание 3300








































































































Результаты поиска

Содержание 3300

Отзывы:

Похожие инструкции для 3300

Бренды по названию

Популярные бренды

Jabiru 3300, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 3300

Отзывы:

Похожие инструкции для 3300

Бренды по названию

Популярные бренды