manualshive.com logo in svg

Jabiru 3300, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Jabiru 3300 Скачать руководство пользователя страница 33

Page No: 33 

Issue No: 1   

 

Date: 031100 

Issued By: PJA 

36 

Remove Thrust Washers (front and rear) 

 

 

- 2 without tang on right half case 

 

 

- 2 with tang on left half case 

 

 

Note   - visually check for marks or scratches 

 

 

 

- keep matched to their seats   

 

- 

 
37 

Remove Main Bearing Inserts (16)   

 

 

- 

 

 

Note  - visually check for marks or scratches

 

 

 

 

- keep matched to seats

 

 
38 

Remove Crankcase dowels.  Remove O'Rings and Discard  - 

 

 

Note -  do not attempt to remove studs as they 

 

 

 

 

are loctited in with 620 loctite

 

 
39 

Remove Oil Gallery Plugs and Oil Pressure Sender.  

- 

 

 

Remove Oil Relief Valve. 

 
 

Cylinder Head Disassembly

 

 
40 

Remove Valve Springs and Valves 

   Valve 

Spring 

 

 

 

 

 

 

 

 

 

 

 

Compressor 

 
41 

Remove Push Rod Circlips and O'Rings 

 

 

Internal Circlip Pliers 

 
 

Gearbox Cover Disassembly

 

 
42 

Remove Distributor Shafts   

 

 

 

- 

 
43 

Remove 

Oil 

Seals 

     - 

 
 

Crankshaft & Camshaft Disassembly

 

 
44 

Remove Bolts from Conrod   

 

 

 

1/4” Allen Key 

 

 

Note  - Rods will need to be heated

  

 

3/8 Ratchet 

 

 

 

- Big End Bolts are Discarded on Removal

  Hot Air Gun Rags 

 
45 

Remove Rod Bearing Inserts 

 

 

Note  - visually inspect for marks and scratches

 - 

 

 

 

- keep matched to their seats

 

 
46 

Remove Camshaft Gears.  Discard Camshaft Bolts.   

- 

 

 

Remove welsh plug in rear of camshaft. 

Содержание 3300








































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды