J.E. Adams 75000-SWL Series Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 31

background image

INSTALLATION:

hose to arch

– Screw hose inlet hand tight into end of boom arm. No sealant is required. Slide hose clamp

and rubber 2” x 1.5” hose adapter over barbed end of metal hose adapter.  Leave at least
3/4” gap from end of rubber hose adapter to flange on  metal hose adapter.** Tighten hose
clamp over rubber adapter to metal adapter interface. Thread 1 ½” x 25’ hose into rubber
hose adapter.  Insert metal adapter into hose inlet, the adapter will be held into place by the
prongs on the spring lid of inlet. Next determine the length of the hose required for your
application and cut off excess that may not be needed.

22

Hose Inlet

Metal Hose

Adapter

Rubber Hose

Adapter 2” slip on

to 1.5” hose thread

Hose Clamp

1-3/4

– 2-3/4

1.5” Hose

REV 12-1-20

**Optional 6063-7W
small boom does not
contain metal
adaptor and
threaded hose inlet.

«
...
20
21
22
23
24
...
»

Содержание 75000-SWL Series
































Отзывы:

Нет отзывов

Похожие инструкции для 75000-SWL Series

Бренд: Haier Страницы: 28

Бренд: Olimpia splendid Страницы: 52

Бренд: Soleus Air Страницы: 16

Elektra Health+ 8077

Бренд: S&P Africa Страницы: 6

Бренд: Crane Страницы: 14

Бренд: Gree Страницы: 16

Evaporative Humidifier

Бренд: Vornado Страницы: 10

ACTIVE AIR AADHC45P

Бренд: Hydrofarm Страницы: 28

Бренд: SAN-UP Страницы: 12

Бренд: Eberg Страницы: 16

Бренд: Trident Страницы: 41

Бренд: Prem-I-Air Страницы: 5

Бренд: KDK Страницы: 40

Бренд: NANO Страницы: 27

Бренд: Qlima Страницы: 60

Бренд: Magic Care Страницы: 12

Dehumidifier S1

Бренд: Lanaform Страницы: 76

Бренд: Dantherm Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды