J. A. Roby FORGERON, Инструкция по эксплуатации

Страница: 26 / 30

26
March 1 st , 2015
The door is the mobile element that need a special attention.
Its tightness is primordial. One of the first signs of wear braided
fiberglass rope is the white soot seems to stick on the glass
located where the air leak.
Air Tighten Adjustment.
If the braided fiberglass rope still seems good enough and little
flatten it need probably to be tighten
Door adjustment (hinges side).
Important: To keep squareness of the door Keep the door
locked and loosen only one hinge at a time..
1) Loosen lightly upper hinge
2) Push the door right beside the upper hinge to tighten
the braided fiberglass rope. Then tighten the hinge.
3) Loosen lightly lower hinge.
4) Push the door right beside the lower hinge to tighten
the braided fiberglass rope. Then tighten the lower
hinge.
5) Open the door and insert a piece of paper between
the frontage of stove and the braided fiberglass rope
and close it.
6) If the paper easily slide when you pull it, do steps 1 to
5 another time.
7) If after some try the piece of paper slide easily. The
braided fiberglass rope must be changed.
Door adjustment (right side)
This side adjustment is do with the screw under the door near
the hook hole..
1) Unlock and open the door.
2) With a screwdriver turn clockwise the adjustment
screw a quarter turn.
3) Put a piece of paper between the frontage of stove
and braided fiberglass rope and close and lock the
door.
4) If the paper easily slide when you pull it, do steps 1 to
3 another time.
5) If the door side touch the frontage of the stove and the
piece of paper slide easily. The braided fiberglass
rope must be changed.
On some version of stove two screw is for retain the door.
Cleaning up glass
To clean the glasses, J.A. Roby Inc. recommends using
products sold for this purpose or an oven cleaner avoiding
touching paint part.
•
Avoid cleaning with abrasives or when the glass is
hot. Cleaning glass when is hot can cause a thermal
shock and broken the glass.
Uninstalling and installing door.
To uninstall keep the lower hinge tighten.
1) Keep the door lock.
2) Untighten the upper hinge without remove the nut.
3) Unlock the door and carry it while open.
4) Tilt the door off the upper hinge
5) Lift the door off the lower hinge..
Installing the door.
1) Insert the bottom hinge
2) Close the door align it and lock it.
3) Tighten the upper hinge then align the washer with
the hinge support.
4) Do the air tighten adjustment.
Broken glass replacement.
WARNING: NEVER OPERATE STOVE WHEN THE GLASS
IS BROKEN OR CRACK
Replace only with a 5mm ceramic glass with the right shape.
DO NOT USE SUBTITUTE
Steps to replace glass.
1) Loosen partially the screws retaining the four glass
supports. And remove the support. (On the cook stove
door remove completely the screw.)
2) Remove the broken glass and all pieces of broken
glass. And clean the door.
3) Stick the flat fiberglass rope around the glass without
pulling it excessively. A sticking side is already on the
flat rope.
4) Install the new glasses and put the lower support first
and gently tighten screw. Tighten it too much can
make a pressure point and can break the glass when
it became hot.
5) Install the top support and gently tighten screw
6) Check the tightening Tighten it too much can make a
pressure point and can break the glass when it
became hot
If you cannot replace glass in place you may have to remove
the door to make it. Look in this manual to know how.
Fiberglass rope replacement.
Use a ½ inches (12.7mm) braided fiberglass rope.
It is possible to replace the braided fiberglass rope with the
door on the stove, but if you want you can remove door.
Fiberglass rope preparation.
1) Take the end of the fiberglass rope and push fiber
inside to make a clean end.
2) Add little touch of high temperature latex inside the
end of the fiber glass rope.
3) Remove old fiberglass rope and clean the groove
4) Starting at the lower corner near the hinge put the
fiberglass rope into the grove without giving any
tension and cut it ½ inches over the require length
5) Take the fresh cut end of the fiberglass rope and push
the fiber inside to make a clean end.
6) Add high temperature latex inside the end of
fiberglass rope.
Fiberglass rope installation.
1) Put a high temperature latex inside the clean groove
to glue the fiberglass rope.
2) Starting at the lower corner near the hinge put
fiberglass rope into the groove without giving any
tension