background image

- 15 -

1. Before Use

For reliable pump performance to suit your application purposes, full safety measures should be taken for

the pump unit and the entire system.  The following information, including the points to be observed in the

handling of the pump, deals with the measures to ensure the safe operation of the system.  Please read

the description carefully.

To operate this pump, a 5-port solenoid valve and a controller (AC-1 type, FD type, SC type or FDC-1

type) are required.

In addition, to enhance system safely, a quick exhaust valve must be installed.

No.

Points to be Observed

Description

1

Pump stroke speed:

Do not run pump exceeding the max.

stroke speed which is shown on the

item 4.  Specifications on page 8.

¡

If many air bubbles are sucked through pump suction port, pump

is put into state of air locked operation and stroke rate will rise to

abnormal levels.  Safety measure should be taken so that pump

does not run at speeds above max. stroke speed.  With FD, SC or

FDC-1 controller, the upper limit of stroke speed can be set.

2

Supply air pressure must be

maintained within specified

pressure range.

¡

In view of pressure resistance of filter at medium temperature,

provide air under as low pressure as possible, for protection of

bellows & to ensure safety.

¡

Any fluctuation in pressure of supplied air causes change in

discharge.  Attach reducing valve to stabilize pressure.

4

Prohibited liquids

Caution

Following liquids must not be used.

• Liquids that are easily crystallized

• Liquids containing slurry

• Low conductivity carbon hydrate

liquid

¡

Service life of valve & bellows is shortened with use of liquid that

is easily crystallized or contains slurry.  Use of such liquids is not

recommended.

¡

If solvent naphtha is used, electrostatic destruction may be

generated between fluororesin & liquid, finally producing

pinholes.

3

Liquid temp. range

¡

Temp. of pumped liquid must be within the range of 5-180 deg.C.

Pump type

Liquid temperature range Supply air pressure range

FS-15·30·60

5-50 deg.C

0.147-0.490 (MPa)

51-100 deg.C

0.147-0.294 (MPa)

101-180 deg.C

0.147-0.196 (MPa)

Содержание FS-15HT1











































Отзывы: