IVT AC-100L2C, Инструкция по эксплуатации

Страница: 9 / 68

9
EN
Instruction manual
∙ When using the machine for different purposes
(inflating, supplying pneumatic instruments and other
units utilizing compressed air power, painting, washing
etc...), the user is supposed to be aware of safety
regulations for each specific case.
∙ Ensure all air tools and accessories used are
designed for the working pressure or are supplied via a
pressure regulator.
∙ The machine is intended for continuous unattended
operation. Ensure that the machine is mounted far
from inflammables and no external factors prevent the
normal cooling of the machine.
WARNING! Operation in hazardous
locations is not permitted.
∙ The machine must not be used in the areas with
dust or containing explosive gases and vapours of
aggressive substances.
∙ It is prohibited to leave the machine in the rain or
snow as well as to operate it in high humidity.
∙ Do not touch the machine with wet hands.
WARNING! Do not direct a jet of
compressed air at people, animals
or at your own body. Do not direct
a jet of compressed air (or sprayed
substances) at the machine.
∙
Ensure all screwed connections are fully tightened
at all times.
∙
Do not attempt to repair the device yourself! Only
trained specialists are permitted to service or repair
compressors, pressure vessels and air tools.
CAUTION! Risk of burns from
the surfaces of parts carrying
compressed air! Pay attention not to
touch hot surfaces or hot parts. Let
the device cool off before servicing.
CAUTION! Risk of burns from
the surfaces of parts carrying
compressed air! Pay attention not to
touch hot surfaces or hot parts. Let
the device cool off before servicing.
CAUTION! Risk of burns from
the surfaces of parts carrying
compressed air! Pay attention not to
touch hot surfaces or hot parts. Let
the device cool off before servicing.
∙
WARNING! Never inhale air from the
compressor either directly or from
a breathing device connected to the
compressor. Work in an area with
good cross-ventilation.
Use safety equipment! Wear hearing protection.
Wear safety glasses. Wear mask respirator when work
generates dust or mist detrimental to health.
∙ Please note that the compressor will start
automatically when the pressure falls off to a minimum! –
disconnect from power supply prior to any servicing. Start
the machine only when a tool is connected. Connect and
disconnect the tool only when the machine is off.
∙ Never unscrew any connecting parts when the
receiver is in pressure condition.
∙ Do not leave compressed air in the receiver.
Transferring or keeping machine with air not released
from the receiver is prohibited.
∙ After the work is finished, wait until the machine is
cooled down. Only then, the machine may be covered
or encased in the protective casing.
∙ ATTENTION! The compressor should be located
as close to the main supply as possible. NEVER USE
an extension cord with this product. Use additional air
hose instead of an extention cord to avoid power loss
and permanent motor damage.
∙ ATTENTION! This appliance must be earthed
with electrical grounding: failure to provide adequate
grounding to this product could result in serious injury or
death from electrocution.
UNPACKING
When unpacking, check to make sure that all
components are included. Refer to the drawings on this
manual. If any parts are missing or broken, please call
an IVT assistance center.
ASSEMBLY INSTRUCTIONS
When performing the following operations, do not apply
excessive force to tight fasteners. Inobservance of this
requirement may lead to the damage of threaded joints.
Important! You must fully assemble the appliance
before using it for the first time.
Mounting the wheels (20) and rubber feet (18) [F1]
In case the wheels (20) are not mounted on the
machine, after unpacking, mount the wheels (20) and
rubber feet (if present) appropriately.
Mounting the air filter (17)
If not already mounted, it’s necessary to install the air
filter (17) on the machine.
∙ First, remove the transportation stop with a
screwdriver or similar, and then screw the air filter (17)
securely to the cylinder head.
INITIAL OPERATION
Always use the correct supply voltage: the power supply
voltage must match the information quoted on the tool
identification plate.