IVM Vent-Tech SWG B Series Скачать руководство пользователя страница 10

www.internationalvalve.com

 

 

 

INSTALLATION, OPERATION AND MAINTENANCE MANUAL 

MODEL SWG, SERIES C, B, V, N 

 

International Valve Marketing, LLC

 

Page | 10

 

Last Revision Date: 09/13/2013

 

 

 

Two  side  ports  are  provided  on  each  valve.    The  upper  port  is  called  the  gauge  port  and  the 
lower port is called a pressure relief port.  After gaining a familiarity with the pipeline conditions 
and your Vent-Tech valve, these ports utilized together can serve as flushing ports to flush the 
valve without requiring disassembly and re-assembly of the valve.  Using the upper port as the 
inlet and the lower port as the outlet, a certified system maintenance mechanic can: 

 

Close the isolation valve and depressurize the valve.  

 

 

Flush a stream of water with a maximum recommended temperature of 160o F through the 
valve.  In the rare occasion where temperatures above 180

o

 F are beneficial, please contact 

IVM engineering.  

[email protected]

 

 

Continue flushing the valve until water runs clear 

 

Consult local requirements for handling of pipeline emissions. 

An example maintenance worksheet is included in the Addendum at the end of this manual 

(d)

 

Troubleshooting Air Valve Problems  

This

 section contains a table that describes possible solutions to problems that may occur when using 

your air valve. The table contains:  

• 

Symptoms 

that describe the type of problem.  

• Reasons 

for the problem 

• 

Possible solutions 

that describe what you should do to try to solve the problem.  

 

 

 

 

 

 

 

 

 

Trouble Shooting 

Symptom 

Reason 

Possible Solutions 

Leak at Large Orifice 

Debris stuck in valve 

Follow enclosed Maintenance 
Instructions 
 

Leak thru Center anti-
surge orifice 

Nozzle not sealed in Nozzle Float 

Follow enclosed Maintenance 
Instructions 
 

Leak at Sealing Flange and 
body flange 

Sealing Flange not secured 

Tighten Sealing Flange Fasteners 

Small volumes of water 
evident on top of Anti-
Surge Float or top Sealing 
Flange during start-up 

Normal operation of valve 

No solution required 

WARNING!     POTENTIAL SCALDING HAZARD!  

Using hot water at temperatures above 120

o

 F poses the risk of personal injury if proper awareness,, 

care and attention guidelines are not followed. 

Содержание Vent-Tech SWG B Series
















Отзывы: