ITW Simco-Ion Conveyostat Скачать руководство пользователя

Страница: 15 / 19

5100577 Rev L

CONVEYOSTAT IN-LINE IONIZER

7. TROUBLESHOOTING

NOTE –

Only qualified service personnel are to perform troubleshooting

tasks.

CAUTION – Electrical Shock Hazard

Do not troubleshoot high voltage components with power supply

energized.

Disconnect input power or switch power off before troubleshooting

Conveyostat with BPS-C

PROBLEM

CAUSE

SOLUTION

Power indicator

NOT illuminated

Power not on at power supply

Turn on Power switch on end of power supply case

Poor electrical connections

Check input power connections, both 24 VDC and

line voltage; check modular cable if used with a

Control Station

Defective AC adapter

Replace AC adapter

Blown device fuse in Control Station

Try another modular connector on Control Station

Clean Bar indicator

illuminated

Process material fouling static bar ion emitters

Remove process material from static bar

Dirt build-up on ion emitters or conductive

contamination on face of bar

Clean ion emitters and static bar

See Maintenance section for details

Bar ON indicator

NOT illuminated

No static bar connected

Install static bar and connect to power supply

High voltage connector is not connected

Turn off power, reconnect high voltage cable and

secure plug with captive screws

High voltage connector missing bar type sense

pin at BPS-C

Replace high voltage connector plug at BPS-C

Bar power off at Control Station

Turn bar power on through device page on Control

Station

Fault indicator

illuminated

Static bar shorted to grounded metal

Clear debris shorting static bar to grounded metal

Damage to high voltage connector

Replace high voltage connector

Damage to high voltage cable

Replace defective cable

High voltage module inside power supply faulty

Replace high voltage module

Locked indicator

NOT illuminated

Power supply operating stand-alone

Locked indicator only illuminates if Control Station

connected

Poor electrical connection

Check connections of modular cable at power supply

and Control Station

Содержание Simco-Ion Conveyostat




















Результаты поиска

Содержание Simco-Ion Conveyostat

Отзывы:

Похожие инструкции для Simco-Ion Conveyostat

Бренды по названию

Популярные бренды

ITW Simco-Ion Conveyostat, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Simco-Ion Conveyostat

Отзывы:

Похожие инструкции для Simco-Ion Conveyostat

Бренды по названию

Популярные бренды