ITT Goulds Pumps VICR Скачать руководство пользователя | Manualshive

Страница: 14 / 75

background image

Table 1: Methods

Pump type

Lifting method

A fully-assembled pump

Use suitable lifting devices attached to the lifting lugs on the discharge head or hoist
rings on the discharge head base flange.

A partially-assembled pump Use suitable lifting devices attached to the component or sub-assembly lifting lugs or

suitable swivel hoist rings through the component flanges, bolt holes.

A disassembled pump

Use suitable lifting devices attached to the component lifting lugs or suitable swivel
hoist rings through the component flanges, bolt holes.

NOTICE:

Rig the bowl assembly from the discharge head or column adapter and from the suction bell.
Never rig the bowl assembly from the tie-rods.

Example: VICR lifted from horizontal to vertical

Figure 2: VICR horizontal position

2.3 Pump handling, rigging and lifting

12

Model VICR Installation, Operation, and Maintenance Manual

«
...
12
13
14
15
16
...
»

Содержание Goulds Pumps VICR












































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps VICR

Бренд: Waterstone Страницы: 6

Бренд: Zoeller Страницы: 4

Бренд: Mallory Страницы: 7

Бренд: Macnaught Страницы: 12

Бренд: A.O. Smith Страницы: 2

Бренд: Samoa Страницы: 36

WILDEN P100 Advanced Plastic

Бренд: PSG Dover Страницы: 28

Бренд: Vagner Pool Страницы: 35

Бренд: Idex Страницы: 40

Бренд: Galletti Страницы: 60

Бренд: Enviro Страницы: 112

Бренд: Heat-Flo Страницы: 20

Бренд: Varian Страницы: 24

Water Quality System EQHP-TWIN 108SP

Бренд: Bunn Страницы: 2

Бренд: Flotec Страницы: 16

SUF-130- 300/400/500

Бренд: State Water Heaters Страницы: 76

Бренд: Jieguan Страницы: 21

Бренд: Eco-Smart Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды