ITT Goulds Pumps VCW Скачать руководство пользователя | Manualshive

Страница: 19 / 71

background image

4 Installation

4.1 Pre-installation

Precautions

WARNING:

•

When installing in a potentially explosive environment, ensure that the motor is properly
certified.

•

All equipment being installed must be properly grounded to prevent unexpected dis-
charge. Discharge can cause equipment damage, electric shock, and result in serious in-
jury. Test the ground lead to verify it is connected correctly.

NOTICE:

•

Electrical connections must be made by certified electricians in compliance with all inter-
national, national, state and local regulations.

•

Supervision by an authorized ITT representative is recommended to ensure proper instal-
lation. Improper installation may result in equipment damage or decreased performance.

4.2 Pre-installation

Precautions

WARNING:

•

When installing in a potentially explosive environment, ensure that the motor is properly
certified.

•

All equipment being installed must be properly grounded to prevent unexpected dis-
charge. Discharge can cause equipment damage, electric shock, and result in serious in-
jury. Test the ground lead to verify it is connected correctly.

NOTICE:

•

Electrical connections must be made by certified electricians in compliance with all inter-
national, national, state and local regulations.

•

Supervision by an authorized ITT representative is recommended to ensure proper instal-
lation. Improper installation may result in equipment damage or decreased performance.

4.2.1 Inspect the sub-base

1.

If an optional sub-base is furnished, remove it from the pump discharge head when it is shipped
assembled.

2.

Completely clean the underside of the sub-base.
You might need to coat the underside of the sub-base with an epoxy primer which you can pur-
chase as an option.

3.

Remove the rust-preventative solution from the machined topside of the barrel flange with an appro-
priate solution.

4 Installation

Model VCW Installation, Operation, and Maintenance

17

«
...
17
18
19
20
21
...
»

Содержание Goulds Pumps VCW








































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps VCW

Бренд: EBARA Страницы: 16

Бренд: EBARA Страницы: 40

Бренд: EBARA Страницы: 38

Бренд: Zip Страницы: 12

Бренд: Dantherm Страницы: 12

Бренд: York Страницы: 24

Бренд: Nagman Страницы: 15

MAG HK 13-2/0-3 H

Бренд: Vaillant Страницы: 12

Бренд: Astral Pool Страницы: 35

Бренд: IWAKI PUMPS Страницы: 32

Бренд: salmson Страницы: 16

Бренд: Binks Страницы: 22

Бренд: W'eau Страницы: 32

Бренд: DVP Страницы: 13

Бренд: Acquaer Страницы: 8

DIESELFI Series

Бренд: FMT Страницы: 14

Бренд: DAYLIFF Страницы: 12

Бренд: A.O. Smith Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды