ITT Goulds Pumps ICM Скачать руководство пользователя | Manualshive

Страница: 17 / 40

background image

3 Transport and storage

3.1 Transport and storage

WARNING:

The pump or the unit must be transported properly. It must be ensured that during transport the
pump/unit remains in the horizontal position and does not slip out of the transport suspension
points.

A pump or motor can be suspended from the ring bolt provided for this purpose.

The suspension points are not suitable for transporting a complete unit, i.e. pump with base plate and
motor.

In this case, the slinging points for the ropes on the base plate are to be used.

Figure 5: Slinging points for ropes on baseplate

The slinging ropes must not be attached to free shaft ends or to the ring bolt of the motor.

NOTICE:

Directly after receipt of the goods, the consignment must be checked for completeness and
any in-transit damage.

Damaged pumps must not be installed in the plant.

3 Transport and storage

Model ICM/ICMP Magnetic Drive Chemical Process Pump with Grease Bearing Lubrication Installation, Operation, and
Maintenance Manual

15

«
...
15
16
17
18
19
...
»

Содержание Goulds Pumps ICM









































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps ICM

Бренд: Waterous Страницы: 13

Бренд: Waterous Страницы: 8

Бренд: Navien Страницы: 83

Бренд: EINHELL Страницы: 44

SUPER T T6A60S-4LE2X FT4 Series

Бренд: GORMAN-RUPP PUMPS Страницы: 48

Бренд: IWAKI PUMPS Страницы: 32

MiniTank WM-2.5

Бренд: Waiwela Страницы: 20

Cascademax Series

Бренд: ubbink Страницы: 54

DIO 45/13 fl ex

Бренд: T.I.P. Страницы: 52

DynaDrive DD60-10

Бренд: Davey Страницы: 32

Бренд: JABSCO Страницы: 14

Бренд: Walrus Pump Страницы: 12

Бренд: Navien Страницы: 60

FLOJET R3521/03521 Series

Бренд: Xylem Страницы: 4

Бренд: Nakayama Страницы: 29

Бренд: TCM Страницы: 127

Бренд: Samoa Страницы: 10

Бренд: Pattfield Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды