ITT GOULDS PUMPS 3935 Скачать руководство пользователя страница 27

Страница: 27 / 37

Table 6: BP70 impeller stack clearance

BP70 Impeller Stack

Required Front Clearance

1st stack

1O stages or less

+1.016mm ± 0.127mm | +0.040" ± 0.005"

2nd stack

11th to 20th stages

+0.508mm ± 0.127mm |+0.020" ± 0.005"

3rd stack

21st to 30th stages

+0.508mm ± 0.127mm |+0.020" ± 0.005"

4th stack

31st to 40th stages

+0.635mm ± 0.127mm |+0.025" ± 0.005"

5th stack

41st and 42nd stages

+0.762mm ± 0.127mm |+0.030" ± 0.005"

NOTICE:

1. Steady bearings are located between each stack - every 10 stages.

2. Use only 0.254mm | 0.010" shims for setting front clearance of impellers 25, 31 and 35.

3. At completing of stacking remove one 0.254mm | 0.010" shim from front of (suction side) im-
pellers 25, 31 and 35.

Table 7: BP100 impeller stack clearance

BP 100 Impeller Stack

Required Front Clearance

1st stack

8 stages or less

+1.016mm ± 0.127mm | +.040" ±.005"

2nd stack

9th to 16th stages

+0.508mm ± 0.127mm | +.020" ±.005"

3rd stack

17th to 24th stages

+0.508mm ± 0.127mm | +.020" ±.005"

4th stack

25th to 32nd stages

+0.635mm ± 0.127mm | +.025" ±.005"

5th stack

33rd to 40th stages

+ 0.762mm ± 0.127mm | +.030" ±.005"

6th stack 41st stage

+0.889mm ± 0.127mm | +.035" ±.005"

NOTICE:

1. Steady bearings located between each stack - every 8 stages.

2. Use only 0.254mm | 0.010" shims for setting front clearance of impellers 21, 29, 33 and 37.

3. At completion of stacking remove one 0.254mm | 0.010" shims from front of (suction side)
impellers 21, 29, 33 and 37.

7.7 Bearing and seal replacement

Model 3935 Installation, Operation and Maintenance Instructions

Содержание GOULDS PUMPS 3935






































Результаты поиска

Содержание GOULDS PUMPS 3935

Отзывы:

Похожие инструкции для GOULDS PUMPS 3935

Бренды по названию

Популярные бренды

ITT GOULDS PUMPS 3935, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GOULDS PUMPS 3935

Отзывы:

Похожие инструкции для GOULDS PUMPS 3935

Бренды по названию

Популярные бренды