manualshive.com logo in svg

ITS Telecom 1700264, Руководство по эксплуатации

Поделиться
Скачать
ITS Telecom 1700264 Скачать руководство пользователя страница 17

MITS Janus Time Engine              

Page 17 of 39 

Copyright© Instrumentation Technology Systems 2020 

 

 

 

20200929 

 

The drop down list (IRIG, GPS (if present), PTP/NTP, 1PPS) is 
the same in each selection, however, if IRIG is selected as priority 
1 (as shown), this selection will not be accepted for any other 
priority.   
A priority level may not be skipped.  That is if an input for 
priority 1, 3 and 4 is selected (skipped priority 2), fail order will 
not work.  Loss of IRIG as shown as priority 1 will not result in 
selection of the priority 3 choice as in this example choice 2 
would be blank.   
When a time reference is selected, that status of that source is 
displayed.  Green indicates that it is selected and is a valid source.  Yellow indicates that it can 
be used as a time reference, however it is not being used as the reference and the time master is 
not locked to it.  If the indicator is dark (gray), this input is either not available or has been 
invalidated by the MJTE for some error conditions.   Consequently, this reference will be 
skipped over if a fail over sequence is initiated.   

If 

Save List

 is clicked, the current priority list is saved to MJTE flash memory and will be the 

default priority list at power up until changed.  If 

Clear List

 is selected, this list will be cleared 

from MJTE flash memory and will not be shown on the page. 

3.4.2

 

TCP/IP Frame 

The TCP/IP frame provides the ability to set the Janus TCG to receive addresses from a DHCP 
server (factory default) on the network to which it is attached.  When 

Use DHCP

 is checked it 

will cause the Janus TCG to automatically connect to your network.   
In DHCP mode, the Janus TCG will attempt to receive an 
address from a DHCP server for two (2) minutes.  In the event 
there is no DHCP server on the network or it is not accessible 
to the Janus TCG, is will automatically revert to STATIC IP 
mode.  In this mode, connectivity may be achieved by a host 
on the network able to address it via the current STATIC 
address.     
The current mode status reflects 

STATIC 

or

 

ASSIGNED 

(DHCP).  When assigned, the assigned address data is shown 
in the ADDRESS box and on the front panel of the Janus 
TCG. 
The Factory Default static address is 192.168.150.90 with a Gateway of 192.168.150.100 and a 
Subnet Mask of 255.255.255.0.   These values may be changed at any time within the 

TCP/IP

 

frame by entering them and clicking 

Change

.  The values will not be saved until the 

Change

 

button is clicked.  When clicked, the values become effective immediately and are saved to 
internal FLASH memory which will cause them to survive a power cycle.   
While the static address, gateway and subnet mask may be any valid value, they must be values 
that are available and accessible within the applicable network. 
 

Содержание 1700264








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды