Itel STL-SAT Changeover Скачать руководство пользователя страница 23

Страница: 23 / 57

Display Function

SwapChans=ON

<input close for while TC_SWAP> SwapChans=OFF
<input close for while TC_SWAP> SwapChans=ON

GPIO Enab:<ON/OFF>

:if ON, you can control the exchange of master / backup channels using the

GPIO port.

In OFF mode, the outputs will still be piloted, but the unit will not accept

commands from this interface.

NOTE: The GPIO input must only be enabled if the optional GPIO card has been installed

In: xxx

:Decimal value representing the state of the inputs.

SwapChans:<ON/OFF>

:if ON, the master / backup channels will be exchanged.

The SwapChans function is intended as a temporary mode and will be indicated in the status window with
a warning.

Eth:

if set to 1 enables the Ethernet communication interface if it is installed.

2.5.2

Reading Parameters

The second submenu of the system displays the parameters related to the power supplies and their alarm
conditions

BattV:

battery voltage connected to the rear input. Voltage is considered correct if greater than 20V.

Alm: (ON/OFF)

if it is ON (ON), an alarm will be generated if the battery voltage is less than 18V.

Mains:(OK/NO)

indication of the status of the network power supply.

AlmMin:(1..255/OFF)

timeout in minutes for sending the alarm message for missing network. A message

will be sent after the network is missing for a longer time than the one set, and after the same period of
time, to reboot the network power.

2.5.3

Modem Status and SMS alarms Activation

In the third submenu of the system there are the parameters related to GSM

GSMdBm:

field reading received by the modem. Reading is updated once per second.

SMS:(ON/OFF)

If enabled (ON), enables SMS communication with the device.

IDLE:(IDLE/RECV/SEND/INIT/DEL/BIN)

display of communication activity to PC or modem.

IDLE:

waiting for PC or SMS data from the modem

RECV:

in receiving an SMS message

SEND:

transmission of an SMS message

INIT:

when initializing the modem

DEL:

deleting the received message

BIN:

in binary communication

the numeric value next to the label indicates the secondary code for the current activity.

TestSend:(ON/OFF)

test sending message. When the flag is set to "ON", a test message will be sent to all

Содержание STL-SAT Changeover


























































Результаты поиска

Содержание STL-SAT Changeover

Отзывы:

Похожие инструкции для STL-SAT Changeover

Бренды по названию

Популярные бренды

Itel STL-SAT Changeover, Руководство пользователя

Результаты поиска

Содержание STL-SAT Changeover

Отзывы:

Похожие инструкции для STL-SAT Changeover

Бренды по названию

Популярные бренды