ITech IT-M3300 Series Скачать руководство пользователя

Страница: 7 / 110

IT-M3300 Programing Guide

Compliance Information

Complies with the essential requirements of the following applicable European

Directives, and carries the CE marking accordingly:

⚫

Electromagnetic Compatibility (EMC) Directive 2014/30/EU

⚫

Low-Voltage Directive (Safety) 2014/35/EU

Conforms with the following product standards:

EMC Standard

IEC 61326-1:2012/ EN 61326-1:2013

¹²³

Reference Standards

CISPR 11:2009+A1:2010/ EN 55011:2009+A1:2010 (Group 1, Class A)

IEC 61000-4-2:2008/ EN 61000-4-2:2009

IEC 61000-4-3:2006+A1:2007+A2:2010/ EN 61000-4-3:2006+A1:2008+A2:2010

IEC 61000-4-4:2004+A1:2010/ EN 61000-4-4:2004+A1:2010

IEC 61000-4-5:2005/ EN 61000-4-5:2006

IEC 61000-4-6:2008/ EN 61000-4-6:2009

IEC 61000-4-11:2004/ EN 61000-4-11:2004

1. The product is intended for use in non-residential/non-domestic environments. Use of the

product in residential/domestic environments may cause electromagnetic interference.

2. Connection of the instrument to a test object may produce radiations beyond the specified

limit.

3. Use high-performance shielded interface cable to ensure conformity with the EMC standards

listed above.

Safety Standard

IEC 61010-1:2010/ EN 61010-1:2010

Содержание IT-M3300 Series















































































































Результаты поиска

Содержание IT-M3300 Series

Отзывы:

Похожие инструкции для IT-M3300 Series

Бренды по названию

Популярные бренды

ITech IT-M3300 Series, Руководство по программированию

Результаты поиска

Содержание IT-M3300 Series

Отзывы:

Похожие инструкции для IT-M3300 Series

Бренды по названию

Популярные бренды