ISHIDA OMNi-4000 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 15

ISHIDA OMNi-4000 Скачать руководство пользователя страница 2

OUTLINE

■

Purpose of this manual

This manual is used for reference when removing or replacing the Film Feeder.

■

Symbols in the description

Warning symbols

Symbol

Meaning

WARNING

Indicates information that, if not avoided, may result in loss of life or
serious injury.

CAUTION

Indicates information that, if not avoided, could result in relatively
serious or minor injury, damage to the machine or faulty operation.

Explanatory symbols

Symbol

Meaning

NOTE

Indicates information to call or emphasize for attention to the note.

■

Readers of this manual

This manual is written for use by qualified service personnel to perform maintenance
services for the machine.

• Use by anyone except the above personnel is not permitted.
• This manual may be revised in accordance with modifications made to the machine.
• Copying any part of this manual is prohibited without written permission from Ishida Co.,

Ltd.

©

ISHIDA CO., LTD. 2004-2009

All rights are reserved.

OMNi-4000 Film Feeder Replacement Manual

ii

«
1
2
3
4
...
»

Содержание OMNi-4000
















Отзывы:

Нет отзывов