Isee IGEP v2 Скачать руководство пользователя страница 58

Страница: 58 / 66

IGEP

Hardware Reference Manual

™

is a registered trademar k from ISEE 2007 S.L. The followi ng is provided for informational purpos es onl y.

DOCUMENT FROM ISEE 2007 S.L. Ref: MAN-PR-IGEP0020-RCx

6.1

PINOUT TABLE OF EXPANSION CONNECTOR

Below pin table show you pin out of IGEP

™

v2 expansion connector J990, with functionalities

that you can configure. Each table has several columns:

Pin #

: (JJ:PP format) where JJ means J990 connector and PP means pin number.

TYPE

: What kind of pin and origin silicon chip :

OMAP: processor; PMIC: power management chip; PWR: Power and ground lines

MODE 0, MODE 1, MODE 2, MODE 3, MODE 4, MODE 5, MODE 6, MODE 7

: OMAP3x

pin could be configured up to 7 different modes. Complexity of configuration could be

solved

“

Mux

Utility

for

ARM(R)

Microprocessors

”

http://www.ti.com/tool/pinmuxtool

“gray shading”

marked function names denote the function is already being used on

board and should not be used.

“

green

shading”

function denote is ONLY available on OMAP3530 (not on DM3730)

Functions within [] brackets on column “MODE 0” denote board pin function.

For additional details, please refer to

“OMAP3530/25 Applications Processor”

(

www.TI.com

)

Pin #

TYPE

MODE 0

MODE 1

MODE 2

MODE 3

MODE 4

MODE 5

MODE 6

MODE 7

J990:1

PWR

VIO_1 V8

J990:2

PWR

DC_5V

J990:3

OMAP

mmc2_d at7 [Reset WiFi] mmc2_ cl kin

mmc3_d at3 gpio_139

hsusb3_tll_nxt mm3_rxdm safe_mode

J990:4

OMAP

mcbsp3_dx [TPS65950]

uart2_cts

gpio_140

hsusb3_tll_d4

safe_mode

J990:5

OMAP

mmc2_d at6 [P_Dn WiFi] mmc2_di r_c md cam_shutter

mmc3_d at2 gpio_138

hsusb3_tll_dir

safe_mode

J990:6

OMAP

mcbsp3_clkx [TPS65950] uart2_tx

gpio_142

hsusb3_tll_d6

safe_mode

J990:7

OMAP

mmc2_d at5 [Reset BT]

mmc2_ di r_d1 cam_global_rst mmc3_d at1 gpio_137

hsusb3_tll_stp mm3_rxdp safe_mode

J990:8

OMAP

mcbsp3_fsx [TPS65950]

uart2_rx

gpio_143

hsusb3_tll_d7

safe_mode

J990:9

OMAP

mmc2_d at4

mmc2_ di r_d0

mmc3_d at0 gpio_136

safe_mode

J990:10

OMAP

mcbsp3_dr [TPS65950]

uart2_rts

gpio_141

hsusb3_tll_d5

safe_mode

J990:11

OMAP

mmc2_d at3 [WiFi d ata]

mcspi3_cs0

gpio_135

safe_mode

J990:12

OMAP

mcbsp1_dx

mcspi4_simo

mcbsp3_dx

gpio_158

safe_mode

J990:13

OMAP

mmc2_d at2 [WiFi d ata]

mcspi3_cs1

gpio_134

safe_mode

J990:14

OMAP

mcbsp1_clkx

mcbsp3_clkx

gpio_162

safe_mode

J990:15

OMAP

mmc2_d at1 [WiFi d ata]

gpio_133

safe_mode

J990:16

OMAP mcbsp1_fsx

mcspi4_cs0

mcbsp3_fsx

gpio_161

safe_mode

J990:17

OMAP

mmc2_d at0 [WiFi d ata]

mcspi3_somi

gpio_132

safe_mode

J990:18

OMAP

mcbsp1_dr

mcspi4_somi

mcbsp3_dr

gpio_159

safe_mode

J990:19

OMAP

mmc2_c md [WiFi dat a]

mcspi3_simo

gpio_131

safe_mode

J990:20

OMAP

mcbsp1_clkr

mcspi4_clk

gpio_156

safe_mode

J990:21

OMAP

mmc2_cl k [WiFi dat a]

mcspi3_clk

gpio_130

safe_mode

J990:22

OMAP

mcbsp1_fsr

cam_global_reset

gpio_157

safe_mode

J990:23

OMAP

i2c2_sda

gpio_183

safe_mode

J990:24

OMAP

i2c2_scl

gpio_168

safe_mode

J990:25

PMIC

pmic_regen

J990:26

PMIC

sys_nrespwron

J990:27

PWR

GND

J990:28

PWR

GND

Table 18 Expansion Connector signals

Содержание IGEP v2



































































Результаты поиска

Содержание IGEP v2

Отзывы:

Бренды по названию

Популярные бренды

Isee IGEP v2, Справочник по аппаратуре

Результаты поиска

Содержание IGEP v2

Отзывы:

Бренды по названию

Популярные бренды