Isee IGEP v2 Скачать руководство пользователя страница 35

Страница: 35 / 66

IGEP

Hardware Reference Manual

™

is a registered trademar k from ISEE 2007 S.L. The followi ng is provided for informational purpos es onl y.

DOCUMENT FROM ISEE 2007 S.L. Ref: MAN-PR-IGEP0020-RCx

These connectors allow the access to the LCD signals. Next table shows the si gnals that are on
the JA41 connector (

pins 21 to 28 are not available on IGEP

™

revision B series

), with

functionalities that you can configure. Each table has several columns:

Pin #

: (JJ:PP format) where JJ means JA41 connector and PP means pin number.

TYPE

: What kind of pin and origin silicon chip :

OMAP: processor; PMIC: power management chip; PWR: Power and ground lines

MODE 0, MODE 1, MODE 2, MODE 3, MODE 4, MODE 5, MODE 6, MODE 7

: OMAP3x

pin could be configured up to 7 different modes. Complexity of configuration could be

solved

“

Mux

Utility

for

ARM(R)

Microprocessors

”

http://www.ti.com/tool/pinmuxtool

“gray shading”

marked function names denote the function is already being used on

board by DVI device interface (see section 5.21 DVI-D INTERFACE: JA01).

“

green

shading”

marked function names denote this function is ONLY available on

OMAP3530 (not present on DM3730).

“blue shading”

marked function names denote this function is ONLY available on

DM3730 (not present on OMAP3530).

Functions within [] brackets on col

umn “MODE 0” denote board pin

function.

For additional details, please refer to

“OMAP3530/25 Applications Processor”

(

www.TI.com

)

Pin #

TYPE

MODE 0

MODE 2

MODE 3

MODE 4

MODE 5

MODE 7

JA41:1

PWR

3V3

JA41:2

PWR

GND

JA41:3

OMAP dss_data0 [DVI_DATA0]

uart1_cts

dssvenc656_d0

gpio_70

safe_mode

JA41:4

OMAP dss_data1 [DVI_DATA1]

uart1_rts

dssvenc656_d1

gpio_71

safe_mode

JA41:5

OMAP dss_data2 [DVI_DATA2]

dssvenc656_d2

gpio_72

safe_mode

JA41:6

OMAP dss_data3 [DVI_DATA3]

dssvenc656_d3

gpio_73

safe_mode

JA41:7

OMAP dss_data4 [DVI_DATA4]

uart3_rx_irrx

dssvenc656_d4

gpio_74

safe_mode

JA41:8

OMAP dss_data5 [DVI_DATA5]

uart3_tx_irtx

dssvenc656_d5

gpio_75

safe_mode

JA41:9

OMAP dss_data6 [DVI_DATA6]

uart1_tx

dssvenc656_d6

gpio_76

hw_dbg14

safe_mode

JA41:10 OMAP dss_data7 [DVI_DATA7]

uart1_rx

dssvenc656_d7

gpio_77

hw_dbg15

safe_mode

JA41:11 OMAP dss_data8 [DVI_DATA8]

gpio_78

hw_dbg16

safe_mode

JA41:12 OMAP dss_data9 [DVI_DATA9]

gpio_79

hw_dbg17

safe_mode

JA41:13 OMAP dss_data10 [DVI_DATA10]

gpio_80

safe_mode

JA41:14 OMAP dss_data11 [DVI_DATA11]

gpio_81

safe_mode

JA41:15 OMAP dss_data12 [DVI_DATA12]

gpio_82

safe_mode

JA41:16 OMAP dss_data13 [DVI_DATA13]

gpio_83

safe_mode

JA41:17 OMAP dss_data14 [DVI_DATA14]

gpio_84

safe_mode

JA41:18 OMAP dss_data15 [DVI_DATA15]

gpio_85

safe_mode

JA41:19 OMAP dss_data16 [DVI_DATA16]

gpio_86

safe_mode

JA41:20 OMAP dss_data17 [DVI_DATA17]

gpio_87

safe_mode

JA41:21 OMAP dss_data18 [DVI_DATA18]

mcspi3_clk

dss_data0

gpio_88

safe_mode

JA41:22 OMAP dss_data19 [DVI_DATA19]

mcspi3_simo

dss_data1

gpio_89

safe_mode

JA41:23 OMAP dss_data20 [DVI_DATA20]

mcspi3_somi

dss_data2

gpio_90

safe_mode

JA41:24 OMAP dss_data21 [DVI_DATA21]

mcspi3_cs0

dss_data3

gpio_91

safe_mode

JA41:25 OMAP dss_data22 [DVI_DATA22]

mcspi3_cs1

dss_data4

gpio_92

safe_mode

JA41:26 OMAP dss_data23 [DVI_DATA23]

dss_data5

gpio_93

safe_mode

Содержание IGEP v2



































































Результаты поиска

Содержание IGEP v2

Отзывы:

Бренды по названию

Популярные бренды

Isee IGEP v2, Справочник по аппаратуре

Результаты поиска

Содержание IGEP v2

Отзывы:

Бренды по названию

Популярные бренды