background image

DMM

4880 & DMX

4880 Instruction Book 

Revision 0

 

www.irtelectronics.com 

Page 14 of 16 

4880

DMM_4880

DMX_ib_Rev0.doc 

SNMP with IRT Products: 

 
IRT Electronics currently employs SNMPv1 with its SNMP capable frames. The frame acts as an 

agent

 when fitted 

with a CDM

xxxx module. This module has its own designated slot next to the power supply so as to not affect the 

number of modules that the frame will take. Communication between the 

NMS

, the frame and its loaded modules 

are via this CDM

xxxx module. Note that the 

NMS

 software is third party and not supplied by IRT Electronics. 

 
Ethernet connection for SNMP operation is via an RJ45 connector on the rear of the frame, below the mains inlet. 
Ethernet rate runs at either 10 baseT or 100 baseT. 
 
Frame parameters, such as Name, Address and Location, are set via an RS232 interface, a D9 connector on the 
rear of the frame below the mains inlet. A software terminal emulator, such as Tera Term or HyperTerminal, is 
used for setting and reading the parameters of the frame. 
 
IRT modules that are SNMP compatible need a plug

in SMU

4000 module with a program relevant to the module 

that it is plugged into. Depending on the module, besides the module identification, parameters such as alarm 
states, inputs and controls etc. are communicated to the CDM

xxxx 

agent

 via a data bus on the rear of the frame. 

Thus the CDM

xxxx collects information on what is loaded within the frame, what positions they occupy, and their 

current status for communication to the 

NMS

 when the 

NMS

 sends a request for information.  

 
In the event of a major alarm from any of the SNMP compatible modules, or power supplies, a 

trap

 is 

automatically sent by the CDM

xxxx 

agent

 to the 

NMS

 without any prompting by the 

NMS

. This alerts the operator 

to any fault conditions that may exist that need immediate attention. 
 
 
 
 

 
 

FRU-4000

FRAME

110/240 V  50/60 Hz

0.7 A (max.)

FUSES

110/120 Vac

1A  S.B.

220/240 Vac

500 mA  S.B.

      AS3260 approval no.: CS6346N
Ass. no.: 804692     

+

-

48Vdc

Alarm

RS232 

Ethernet 

IRT SNMP Connections 

IRT modules fitted 

with SMU-4000 

PSU’s

CDM-xxxx

IRT SNMP Frame 

IRT SNMP Frame 

IRT modules fitted 

with SMU-4000 

PSU’s

CDM-xxxx

IP 

Network 

Ethernet Cable 

Ethernet Cable 

Ethernet Cable 

NMS 

IRT SNMP Setup

IRT 

Communications 

www.irtcommunications.com

Содержание DMM-4880

















Отзывы: