background image

Page 6 of 18 

 

 

Do not use a product with a malfunctioning switch. Any power tool that cannot be controlled with 
the power switch is dangerous and must be repaired by an authorized service representative 
before using. 

 

Disconnect the power/air supply from the product and place the switch in the locked or off position 
before making any adjustments, changing accessories, or storing the tool. Such preventive safety 
measures reduce the risk of starting the tool accidentally. 

 

Store the tile saw when it is not in use. Store it in a dry, secure place out of the reach of children. 
Inspect the tool for good working condition prior to storage and before re-use. 

 

Use only accessories that are recommended by the manufacturer for use with your product. 
Accessories that may be suitable for one product may create a risk of injury when used with 
another tool. Never use an accessory that has a lower operating speed or operating pressure than 
the tool itself. 

 

Keep guards in place and in working order. Never operate the product without the guards in place. 

 

Do not leave the tool running unattended. 

Specific Operation Warnings 

WARNING

 

 

Always use the proper personal protective gear, including ANSI Z87.1 compliant eye protection.  

 

Ensure the saw is on a flat level stable surface before use.   

 

Do not use a blade that is rated for less than the table's rated speed.   

 

Ensure the blade comes to a complete stop before removing material. 

 

Only operate with the guards in place.   

 

Do not use toothed blades. 

 

Never attempt to free a stalled wheel without first turning the saw OFF and disconnecting the saw 
from the power source. 

 

Never stand or have any part of your body in line with the path of the wheel. 

 

Avoid awkward operations and hand positions where a sudden slip could cause your hand to 
move into the cutting tool. 

 

Never remove the riving knife. The distance between the cutting blade and the riving knife should 
not exceed 1/5in. 

 

Do not use a cutting blade that is bent, deformed, or otherwise damaged. 

 

Never begin cutting tiles before the machine reaches its full speed. 

 

Do not leave the work area until the tile saw has been switched off and the cutting disc has come 
to a complete standstill. 

 

Never attempt to stop the cutting blade by exerting pressure on the side of the blade. 

 

Always unplug the tile saw before performing any maintenance. 

 

Do not use the tile saw before it has been completely assembled and installed according to the 
instructions. 

 

Do not perform any design, assembly, or construction activities on the table. 

Содержание 61450



















Отзывы: