background image

22

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Pre-Lighting Checklist

Be sure to check these items before the initial lighting of the insert:

c  

Gas pressure has been checked carefully - see 

Page 20

.

c  

All gas fittings have been checked for leaks.

c  

All clearances to combustibles have been met-see 

Page 14

.

c  

All combustible materials have been removed from the area 
in front of the insert.

c  

All vented areas of the insert face are unobstructed.

c  

House is ventilated to clear initial paint curing odors - see 

Page 26

.

c  

All packaging materials have been removed from the firebox.

c  

Firebox liner panels and log set or glass media have been 
installed.

c  

The glass door is in place and is properly sealed.

Operating Instructions

FOR YOUR SAFETY READ BEFORE OPERATING

OPERATION

OPERATING INSTRUCTIONS

1.   The Main Power switch located in the control compartment functions as 

a burner override switch.  When in the OFF position, it will not let the 

burner be turned on by the remote.  When in the ON position, it gives 

the remote full control over burner functions.

2.   See Remote Control System on Page 24 for remote specific operating 

instructions.

TO TURN OFF GAS TO APPLIANCE

1.  Turn the main power ON/OFF switch in the control compartment to 

"OFF."

2.  Turn off all electric power to the appliance if service is to be performed.
3.  Close the main line gas shut-off valve.

WARNING: If you do not follow these instructions exactly, 

a fire or explosion may result causing property damage, 

personal injury or loss of life. 

A. This appliance is equipped with an ignition device which automatically 

lights the pilot. Do not try to light the pilot by hand.

B. BEFORE OPERATING smell all around the appliance area for gas. Be sure 

to smell next to the floor because some gas is heavier than air and will 

settle on the floor.

WHAT TO DO IF YOU SMELL GAS:

•  Do not try to light any appliance.

•  Do not touch any electric switch; do not use any phone in your building.

•  Immediately call your gas supplier from a neighbor’s phone. Follow the 

gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fire department.

C. If any portion of this appliance does not operate as the instructions 

indicate, do not try to repair it, call a qualified service technician.  Do not 

use tools.  Force or attempted repair may result in a fire or explosion.

D. Do not use this appliance if any part has been under water. Immediately 

call a qualified service technician to inspect the appliance and to replace 

any part of the control system and any gas control which has been under 

water.

       WARNING

 

Operation of this appliance when not connected 

to a properly installed and maintained venting 

system can result in carbon monoxide (CO) 

poisoning and possible death.

Содержание Madison Park MPI27









































Отзывы: