background image

STEP C

STEP D

a. Mix  the  concrete  according  to the instructions on the bags. Note that

a  thicker  mix  of  concrete  will  dry stronger than a thin mix. Pour the
concrete into the hole, stopping  approximately 18 inches from the top
of the hole.

b. Insert  the  four  pieces  of Anchor Rebar (U5) into the  hole, pushing each

piece  firmly  to  the  bottom  of  the  hole. The  four  pieces  should  be
arranged in a square approximately 8 inches wide so that each piece of
rebar  will  be  positioned next to the J-Bolts when the  J-Bolt Template
is placed in the cement.

c. Finish  filling the hole to the top with concrete. The top of the concrete

should reach just above the level of the top of the form.

U5

a. Position  the  J-Bolt Template (U1) over  the  hole  as shown.

with the sides of the plate square with the sides of the hole.

b.Push  the  J-Bolts  (U2)  into  the  concrete  until  the   J-Bolt Template  is

resting flat against the surface of the concrete.

c. Grasp  the  tops  of  the   J-Bolts and agitate  the Template  assembly  back

and forth repeatedly to eliminate any air bubbles in the concrete. Lift the
Template  slightly  above  the  concrete  when  agitating .  Make  sure  the
Template  is  resting  on  the  concrete  after  agitating. Form  the concrete
into a downward slope away from the Pole to allow water runoff.

d. Clean off  any concrete that may be on the J-Bolt Template or the exposed

portions of the J-Bolts.

e. Using  a  carpenter

s level, make sure the Template is  square to and level

with the playing surface.

f. Allow the concrete to cure  for  a minimum of  5-7 days  before  installing

the  rest   of  your  basketball  system.  In  cold  ,  wet   weather  or  humid
climates, allow additional time for the concrete to cure.

YOU ARE NOW FINISHED WITH THE INITIAL ASSEMBLY STEPS. DO NOT PRO-

CEED WITH THE ASSEMBLY UNTIL THE CONCRETE HAS FULLY CURED .  CUR-

ING WILL TAKE A MINIMUM OF 72 HOURS. IN HUMID CLIMATES OR WET

WEATHER, ALLOW ADDITIONAL TIME FOR THE CONCRETE TO CURE.

!

!

WARNING

NEVER  USE THE  SYSTEM  WITHOUT FOLLOWING THE  CEMENTING  INSTRUCTIONS .  FAILURE TO
FOLLOW ALL OF THESE INSTRUCTIONS AND WARNINGS COULD LEAD TO SERIOUS PERSONAL INJURY
OR PROPERTY DAMAGE AS LISTED ON PAGE ONE.

5

Playing surface
(Front side)

Anchor
template

Edge of
playing surface

This side faces
playing ground

Содержание HIGHLIGHT HOOPS HIL664









Отзывы: