Iridium Go! WVMTKT2001 Скачать руководство пользователя страница 7

Iridium GO! Vehicular Kit 

 

 

NOTICE:

   

Do not try to reposition the antenna by sliding it on a painted metal surface, as this may 

 

    

scratch the surface.

 

3  Antenna and Cable Installation 

Note: It is recommended that prior to installation, pre-test the complete set-up. This can be done on a bench 
or on the vehicle outdoors. Connect all components to test if everything works fine. Doing so will familiarize 
the user on how the parts go together and guarantees it works prior to installation. Make sure the antenna 
is located outside and the Iridium GO! shows good signal reception for at least 5 minutes during this test 
before you proceed with the installation. Always maintain a separation of at least  30 cm (12 in) from other 
antennas. 

 

 
 

 

emergency situation, preventing or delaying an emergency response. These hazards could 
cause serious injury or death. 

 

       

 

Persons with Pacemakers: 

• 

Should ALWAYS keep Iridium GO! and the antenna more than eight inches 
from their pacemaker when the device is turned ON. 

• 

Should turn Iridium GO! OFF immediately if there is any reason to suspect that 
interference is taking place. 

Failure to heed this warning could result in serious injury or death. 

 

      

 

Do not leave power and antenna ports uncovered. Open power cover only for as long as 
recharging is required, and open antenna cover only when actively using the external 
antenna. Leaving the covers open allows moisture and water vapor to enter the device which 
in turn could lead to corrosion and damage to the device. This could cause fire or could cause 
the device to fail so that it is unavailable in an emergency situation, preventing or delaying 
an emergency response. These hazards could cause serious injury or death. 

 

    

 

Avoid pinching injuries: do not place fingers between or at edge of magnetic mount and metal 
surface.   

Содержание Go! WVMTKT2001


















Отзывы: