Irbit Motorcycle Factory Gear up 2005 Скачать руководство пользователя

Страница: 83 / 96

SERVICE COUPON NO 1. 500 KM

(To be performed between 400 to 600 km)

Date_______________

Odometer reading____________

Change engine oil and filter.

Change transmission oil.

Change final drive oil.

Check condition of the gasoline petcock, remove any contaminants, replace in-line fuel filters.

Check carburetors while idling for synchronous operation.

Check tension of wheel spokes.

Check fasteners for proper tightening.

Check steering column bearings.

Check alternator bolts

10.

Check brake fluid reservoir

The maintenance above has been performed as described.

Owner’s Signature

Service Technician’s Signature

SERVICE COUPON NO 2. 2,500 KM

(To be performed between 2,400 to 2,600 km)

Date

Odometer reading

Change engine oil and filter.

(See Lubrication List, chapter 11)

Check final drive oil level.

Inspect air filter element.

Check fasteners for proper tightening.

Check steering column bearings.

Check all wheels for correct bearing adjustment.

Check brake fluid reservoir.

The maintenance above has been performed as described.

Содержание Gear up 2005

































































































Результаты поиска

Содержание Gear up 2005

Отзывы:

Похожие инструкции для Gear up 2005

Бренды по названию

Популярные бренды

Irbit Motorcycle Factory Gear up 2005, Руководство пользователя

Результаты поиска

Содержание Gear up 2005

Отзывы:

Похожие инструкции для Gear up 2005

Бренды по названию

Популярные бренды