Irbit Motorcycle Factory Gear up 2005 Скачать руководство пользователя | Manualshive

Страница: 79 / 96

background image

79

LIMITED WARRANTY ON EMISSION CONTROL SYSTEM

Irbit MotorWorks of America, Inc., 15411 NE 95

th

St, Redmond, WA 98052, USA (hereinafter IMWA)

warrants that each new 2004 and later Ural motorcycle, that includes as standard equipment a
headlight, taillight and stoplight, and is street legal:

A.

is designed, built and equipped so as to conform at the time of initial retail purchase with all
applicable regulations of the United States Environmental Protection Agency, and the
California Air Resources Board; and

B.

is free from defects in material and workmanship which cause such motorcycle to fail to
conform with applicable regulations of the United States Environmental Protection Agency
or the California Air Resources Board for a period of use, depending on the engine
displacement: of 30,000 kilometers (18,641 miles), if the motorcycle’s engine
displacement is 280 cubic centimeters or greater or 5 (five) years from the date of initial
retail delivery, whichever first occurs.

I.

COVERAGE. Warranty defects shall be remedied during customary business hours at any
authorized IMWA motorcycle dealer located within the United States of America in
compliance with the Clean Air Act and applicable regulations of the United States
Environmental Protection Agency and the California Air Resources Board. Any part or parts
replaced under this warranty shall become the property of IMWA.

In the State of California only, emission related warranted parts are specifically defined

by the state’s Emission Warranty Parts List. These warranted parts are: carburetors,
electronic valves, air box, air cleaner element, spark plug, ignition coil, ignition control valve
module, catalyst, carbon absorber, operating valve for vacuum control.

In the State of California only, Emission Control System emergency repairs, as provided

for in the California Administrative Code, may be performed by other than an authorized
IMWA dealer. An emergency situation occurs when an authorized IMWA dealer is not
reasonably available, a part is not available within 30 (thirty) days, or a repair is not
complete within 30 days. Any replacement part can be used in an emergency repair. IMWA
will reimburse the owner for the expenses, including diagnosis, not to exceed IMWA’s
suggested retail price for all warranted parts replaced and labor charges based on IMWA’s
recommended time allowance for the warranty repair and the geographically appropriate
hourly labor rate. The owner may be required to keep receipts and failed parts in order to
receive compensation.

II.

LIMITATIONS. This Emission Control System warranty shall not cover any of the following:
. Repair or replacement required as a result of
(1) Accident
(2) Misuse

«
...
77
78
79
80
81
...
»

Содержание Gear up 2005

































































































Отзывы:

Нет отзывов

Похожие инструкции для Gear up 2005

Бренд: Cannondale Страницы: 61

Бренд: kellermann Страницы: 2

Бренд: HYOSUNG Страницы: 199

Бренд: B-PWR Страницы: 13

Бренд: MRA Страницы: 9

Бренд: GAS GAS Страницы: 150

Бренд: Miller Страницы: 12

Бренд: hepco & becker Страницы: 2

Бренд: Cycle Protect Страницы: 15

Бренд: AGV Страницы: 64

Бренд: Honeywell Страницы: 93

Бренд: Husqvarna Страницы: 107

Бренд: Husqvarna Страницы: 280

Бренд: Husqvarna Страницы: 162

Бренд: Husqvarna Страницы: 321

Бренд: Husqvarna Страницы: 364

2004 DUAL PURPOSE SM 610

Бренд: Husqvarna Страницы: 188

Бренд: Husqvarna Страницы: 269

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды