background image

iQTS244 

Operator’s Manual

888-274-7744

www.iqpowertools.com

En

gli

sh

Safery Rules

1. KEEP GUARDS IN PLACE

 and in working order.

2. REMOVE ADJUSTING KEYS AND WRENCHES. 

Form habit of checking to see that keys and adjusting 

wrenches are removed from tool before turning it on. 

3. KEEP WORK AREA CLEAN.

 Cluttered areas and 

benches invite accidents. 

4. DON’T USE IN DANGEROUS ENVIRONMENT

. Don’t 

use power tools in damp or wet locations, or expose 

them to rain. Keep work area well lighted.

5. KEEP CHILDREN AWAY.

 All visitors should be kept 

safe distance from work area. 

6. MAKE WORKSHOP KID PROOF 

with padlocks, 

master switches, or by removing starter keys. 

7. DON’T FORCE TOOL

. It will do the job better and 

safer at the rate for which it was designed.

8. USE RIGHT TOOL. 

Don’t force tool or attachment 

to do a job for which it was not designed. 

9. USE PROPER EXTENSION CORD.

 Make sure your 

extension cord is in good condition. When using an 

extension cord, be sure to use one heavy enough 

to carry the current your product will draw. An 

undersized cord will cause a drop in line voltage 

resulting in loss of power and overheating. Table A 

shows the correct size to use depending on cord 

length and nameplate ampere rating. If in doubt, use 

the next heavier gage. The smaller the gage number, 

the heavier the cord.

10. WEAR PROPER APPAREL

 Do not wear loose 

clothing, gloves, neckties, rings, bracelets, or other 

jewelry which may get caught in moving parts. 

Nonslip footwear is recommended. Wear protective 

hair covering to contain long hair.

11. ALWAYS USE SAFETY GLASSES. 

Also use face 

or dust mask if cutting operation is dusty. Everyday 

eyeglasses only have impact resistant lenses, they 

are NOT safety glasses.

SAFETY RULES 

12. SECURE WORK. 

Use clamps or a vise to hold work 

when practical. It’s safer than using your hand and it 

frees both hands to operate tool.

13. DON’T OVERREACH.

 Keep proper footing and 

balance at all times.

14. MAINTAIN TOOLS WITH CARE.

 Keep tools 

sharp and clean for best and safest performance. 

Follow instructions for lubricating and changing 

accessories. 

15. DISCONNECT TOOLS 

before servicing; when 

changing accessories, such as blades, bits, cutters, 

and the like. 

16. REDUCE THE RISK OF UNINTENTIONAL 

STARTING.

 Make sure switch is in off position before 

plugging in. 

17. USE RECOMMENDED ACCESSORIES. 

Consult the 

owner’s manual for recommended accessories. The 

use of improper accessories may cause risk of injury 

to persons.

18. NEVER STAND ON TOOL 

Serious injury could 

occur if the tool is tipped or if the cutting tool is 

unintentionally contacted.

19. CHECK DAMAGED PARTS. 

Before further use 

of the too., a guard or other part that is damaged 

should be carefully checked to determine that it will 

operate properly and perform its intended function 

- check for alignment of moving parts, binding of 

moving parts, breakage of parts, mounting, and 

any other conditions that may affect its operation. 

A guard or other part that is damaged should be 

properly repaired or replaced.

20. DIRECTION OF FEED.

 Feed work into a blade or 

cutter against the direction of rotation of the blade 

or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED 

TURN POWER OFF. 

 Don’t leave tool until it comes to 

a complete stop.  

1.3

Содержание Power Tools iQTS244KIT





































Отзывы: