background image

iQTS244 

Operator’s Manual

888-274-7744

www.iqpowertools.com

En

gli

sh

New iQTS244

 Dry Cut Tile Saw, sold by iQ Power 

Tools or an iQ authorized dealer is warranted to be 

free from manufacturing defects in normal service 

for a one year period from date of purchase by the 

original consumer purchaser. Warranty period for 

rental items is 90 days. 

All iQ products must be registered either through 

our website or by mailing in the Warranty Card in 

order for the warranty to be active and valid. This 

Warranty shall not apply to any parts that have 

been subjected to misuse or improper service, 

damaged in transit or handling, altered or repaired 

by unauthorized representatives, or used with a 

blade that is not recommended by iQ Power Tools. 

Any claim arising under this Warranty must 

be submitted by the original purchaser within 

the Warranty period specified above and must 

include proof of purchase. Within Warranty period, 

options are either to replace or repair any parts or 

components that are found to be defective by iQ 

Power Tools at no charge to the original purchaser. 

iQ Power Tools shall not be responsible or 

obligated to pay for freight or other transportation-

related costs or expenses in connection with any 

defective products, replacements, or components 

that are returned to iQ Power Tools facility or any 

authorized repair station. 

WARRANTY

Parts and labor needed to maintain products, 

and the replacement of components due to normal 

wear and tear, are the purchaser’s responsibility 

and are not covered by this Warranty. All products 

or components replaced under Warranty become 

the property of the manufacturer. All replacement 

parts will be considered to be part of the original 

product and any Warranty on such parts will expire 

concurrently with this original Warranty. 

iQ Power Tools will pay for parts and labor in 

connection with Warranty repairs conducted by 

iQ Power Tools or its authorized repair center. 

Replacement parts installed by anyone else will be 

provided without a charge but this Warranty will 

not apply to labor charges in connection therewith.

IN NO EVENT SHALL ANY LIABILITY UNDER 

THIS WARRANTY EXCEED THE REPLACEMENT 

COST OF ANY DEFECTIVE PRODUCT OR 

COMPONENT THEREOF. iQ POWER TOOLS 

SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR 

CONSEQUENTIAL DAMAGES OR FOR ANY OTHER 

DAMAGE OR LOSS NOT EXPRESSLY ASSUMED AS 

SET FORTH HEREIN.

The Warranty on the terms above is the only 

Warranty. This limited Warranty is expressly 

in lieu of all other Warranties, whether 

expressed or implied.

16.1

Содержание Power Tools iQTS244KIT





































Отзывы: