IPSO DR30 Скачать руководство пользователя страница 3

Страница: 3 / 43

Page 3

ATTENTION: L’ACHETEUR DOIT PLACER L’AVERTISSEMENT
SUIVANT DANS UN ENDROIT CLAIR ET VISIBLE:

AVERTISSEMENT.

Assurez-vous de bien

suivre les instructions donnees dans cette
notice pour reduire au minimum le risque
d’incendie ou d’explosion ou pour eviter tuot
dommage materiel, toute blessure ou la mort.

Ne pas entreposer ni utiliser d’essence ni

d’autres vapeurs ou liquides inflammables dans
le voisinage de cet appareil ou de tout autre
apparell.

QUE FAIRE SI VOUS SENTEZ UNE

ODEUR

DE GAZ:

•

Ne pas tenter d’allumer d’apparell.

•

Ne touchez a aucun interrupteur. Ne pas

vous servir des telephones se trouvant dans
le batiment ou vous vous trouvez.

•

Evacuez la piece, le batiment ou la zone.

•

Appelez immediatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions
du fournisseur.

•

Si vous ne pouvez rejoindre le fournisseur

de gaz, appelez le service des incendies.

l’installation et l’entretien doivent etre assures

par un installateur ou un service d’entretien
qualifie ou par le fournisseur de gaz.

POUR VOTRE SECURITE

Ne pas entreposer ni utiliser d’ essence
ni d’autres vapeurs ou liquides
inflammables dans le voisinage de cet
appareil ou de tout autre appareil.

Содержание DR30












































Результаты поиска

Содержание DR30

Отзывы:

Похожие инструкции для DR30

Бренды по названию

Популярные бренды

IPSO DR30, Руководство пользователя

Результаты поиска

Содержание DR30

Отзывы:

Похожие инструкции для DR30

Бренды по названию

Популярные бренды