iPong V300, Руководство по эксплуатации и инструкция пользователя

Страница: 6 / 7

The iPong Tilt Stand is a
multi-tiered iPong elevation tool,
designed to change ball
trajectory and increase shot
variation . Three heights are
available: 9mm,17mm, or 26mm .
The tilt stand is especially useful
when setting the iPong to shoot
slow balls, or fast backspin balls -
that otherwise might NOT go over the net . A bit of experimentation will be required .
With the tilt stand on the front of the iPong, go up in elevation if balls go into the
net . And go down in elevation if balls go off the table .
6 7
IPONG TARGET GAMES
An iPong Target set is available for FREE if you complete the steps
outlined on the card included in the box . The iPong Target set include 3
targets: Small, Medium, and Large . Below are several games which can
be played using these targets .
A. One, Two, Three.
Place the large target in the left corner of the table . The medium
target in the middle (on the centerline) . And the smallest target on
the far right hand corner of the table . Turn on the iPong and aim for
the large target first . Once you hit this one, then aim for the medium
target . And then finally aim for the small target on the far right . This
game is fun and will improve your accuracy in controlling the
horizontal placement of your shots .
B. The Tower
Stack the three targets on top of each other, with the largest target
on the bottom . The medium-sized target in the middle . And the small
target on top . This target ’Tower’ can be placed anywhere on the
table . Turn on the iPong and aim for the small target first . Once you
hit this one, then aim for the medium target . And then finally aim
for the large target on the bottom . This game is fun and will improve
your accuracy in controlling vertical placement of your shots .
C. Speed Pong
For this game you will set the frequency of the iPong to it’s maximum .
The the targets can be placed anywhere on the table . Turn on the
iPong, and see how quickly you can knock down each of the targets .
This game is fun and will improve your hand-eye speed .
Another variation of the above game can be played with another
player, by using a timer to count how long it took each of you to
knock down the three targets . Quickest time wins .
If ball doesn't go over the net, first correct by
increasing the TOPSPIN control . And test again.
If needed, then increase the BACKSPIN control.
And test again.
If ball goes off the table, first correct by decreasing
the TOPSPIN control. And test again.
If needed, then decrease the BACKSPIN control.
4 0 7 3
4 0 6 2
Using the iPong Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm. The tilt stand
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net. A
bit of experimentation will be required. With the tilt stand on the
front of the iPong, go up in elevation if balls go into the net. And
go down in elevation if balls go off the table.
V300 control adjustments for ball errors
For slower balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For fast backspin balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
Place tilt stand on rear of
iPong. Use for very fast topspin balls.
Position iPong near end of table - OR
in middle of table! Start in lowest
position, and adjust upward as needed.
USING THE IPONG TILT STAND
If ball doesn't go over the net, first correct by
increasing the TOPSPIN control . And test again.
If needed, then increase the BACKSPIN control.
And test again.
If ball goes off the table, first correct by decreasing
the TOPSPIN control. And test again.
If needed, then decrease the BACKSPIN control.
4 0 7 3
4 0 6 2
Using the iPong Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm. The tilt stand
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net. A
bit of experimentation will be required. With the tilt stand on the
front of the iPong, go up in elevation if balls go into the net. And
go down in elevation if balls go off the table.
V300 control adjustments for ball errors
For slower balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For fast backspin balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced: Place tilt stand on rear of
iPong. Use for very fast topspin balls.
Position iPong near end of table - OR
in middle of table! Start in lowest
position, and adjust upward as needed.
If ball doesn't go over the net, first correct by
increasing the TOPSPIN control . And test again.
If needed, then increase the BACKSPIN control.
And test again.
If ball goes off the table, first correct by decreasing
the TOPSPIN control. And test again.
If needed, then decrease the BACKSPIN control.
4 0 7 3
4 0 6
2
Using the iPong Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm. The tilt stand
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net. A
bit of experimentation will be required. With the tilt stand on the
front of the iPong, go up in elevation if balls go into the net. And
go down in elevation if balls go off the table.
V300 control adjustments for ball errors
For slower balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For fast backspin balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
Place tilt stand on rear of
iPong. Use for very fast topspin balls.
Position iPong near end of table - OR
in middle of table! Start in lowest
position, and adjust upward as needed.
If ball doesn't go over the net, first correct by
increasing the TOPSPIN control . And test again.
If needed, then increase the BACKSPIN control.
And test again.
If ball goes off the table, first correct by decreasing
the TOPSPIN control. And test again.
If needed, then decrease the BACKSPIN control.
4 0 7 3
4 0 6 2
Using the iPong Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm. The tilt stand
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net. A
bit of experimentation will be required. With the tilt stand on the
front of the iPong, go up in elevation if balls go into the net. And
go down in elevation if balls go off the table.
V300 control adjustments for ball errors
For slower balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For fast backspin balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
Place tilt stand on rear of
iPong. Use for very fast topspin balls.
Position iPong near end of table - OR
in middle of table! Start in lowest
position, and adjust upward as needed.
If ball doesn't go over the net, first correct by
increasing the TOPSPIN control . And test again.
If needed, then increase the BACKSPIN control.
And test again.
If ball goes off the table, first correct by decreasing
the TOPSPIN control. And test again.
If needed, then decrease the BACKSPIN control.
4 0 7 3
4 0 6 2
Using the iPong Tilt Stand
The iPong Tilt Stand is a multi-tiered iPong elevation tool,
designed to change ball trajectory and increase shot variation.
Three heights are available: 9mm,17mm, or 26mm. The tilt stand
is especially useful when setting the iPong to shoot slow balls, or
fast backspin balls - that otherwise might NOT go over the net. A
bit of experimentation will be required. With the tilt stand on the
front of the iPong, go up in elevation if balls go into the net. And
go down in elevation if balls go off the table.
V300 control adjustments for ball errors
For slower balls, position iPong near center of
table. Start with tilt stand in lowest position,
and adjust upward as needed.
For fast backspin balls, position iPong near
end of table. Start with tilt stand in highest
position, and adjust downward as needed.
Advanced:
Place tilt stand on rear of
iPong. Use for very fast topspin balls.
Position iPong near end of table - OR
in middle of table! Start in lowest
position, and adjust upward as needed.