ipf electronic YT353100 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 19

ipf electronic YT353100 Скачать руководство пользователя страница 6

ESC- button

symbol:

ESC

ESC

Pressing both arrow keys

+

at the same time

results in the

ESC

function.

With the ESC function you can step backwards inside the menu and parameters without
saving the settings.

In order to leave all menus and submenus please press the

ESC

-button again and again

until you are back in the RUN-mode.

keyboard lock

If the device is in the RUN-Mode and you press the arrow keys

+

at the same

time for at least 5 seconds, the keyboard lock will be activated.

The display shows „sLOC“, blinking 3 times.

Now the adjusted settings can be read but not be changed.

For cancelling the Keyboard Lock please press both arrow keys

+

for at least 5

seconds again.

menu / overview

switching point S1

release position S1 / hysteresis S1

analog output active

error function active

press enter 5sec

→ enhanced

press enter , short

switching point S2

release pos. S2 / hyst. S2

MANUAL • Subject to alteration! Version:

June 2017

ipf electronic gmbh • Rosmarter Allee 14 • 58762 Altena

│

Tel +49 2351 9365-0 • Fax +49 2351 9365-19

│

[email protected] • www.ipf-electronic.com

6

«
...
4
5
6
7
8
...
»

Содержание YT353100




















Отзывы:

Нет отзывов