background image

3. Installation

For mounting, the degree of protection specified must be observed. If necessary, protect the unit 

against environmental influences such as sprayed water, dust, knocks, vibrations and extreme 

temperatures. 

3.1 Mounting the magnetic strip 

The mounting surface / measuring track must be flat. Buckles or bumps will lead to measu-ring 

inaccuracies. 

For technical reasons the strip should be approx. 100mm longer than the actual measuring 

distance. 

Attention! 

To guarantee 

optimal adhesion 

oil, grease dust etc. must be removed by 

using cleansing agents which evaporate without leaving residues. Suitable cleansing 

agents are e.g. ketones (acetone) or alcohols; the companies Loctite 

and 3M can both supply such cleansing liquid. Make sure that the surface to be glued is dry and 

apply the strip with maximum pressure. Glueing should preferably be undertaken at temperatures 

between 20°C to 30°C and in dry atmosphere. 

Advice! 

When applying long pieces of magnetic strip do not immediately remove the com-plete 

protective foil, but rather peel back a short part from the end sufficient to fix the strip. Now align 

the strip. The protective strip can then be peeled back and put out from the side while pressing the 

tape firmly onto the mounting surface. A wall paper roller wheel could be used to assist in applying 

pressure onto the magnetic strip when fixing it in position. 

Mounting steps (see fig.1) 

Clean mounting surface (1) carefully.

Remove protective foil (2) from the adhesive side of the magnetic strip (3).

Stick down the magnetic strip (4).

Clean surface of magnetic strip carefully.

Remove protective foil (6) from adhesive tape on the cover strip (5).

Fix cover strip (both ends should slightly overlap).

Also fix cover strip's ends to avoid unintentional peeling.

MANUAL

 • Subject to alteration! Version: 

Juli 2016

 

ipf electronic gmbh

 • Rosmarter Allee 14 • 58762 Altena 

 Tel +49 2351 9365-0 • Fax +49 2351 9365-19 

 [email protected] • 

www.ipf-electronic.com 

2

 

Содержание MW11 Series









Отзывы: