IPC Gansow CT15 B R, Руководство оператора

Страница: 34 / 43

GB
The suction motor does not start the suction button LED is off press the suction button.
There is no power to the suction motor or the
motor is faulty check that the motor power connector is
correctly connected to the main wiring; if
it is correctly connected, have the motor
replaced
>%@ 026)(7WHPSHUDWXUH!ƒ&
[B]= stop the machine, leave to cool
down for 45’
>%@ H[FHVVLYH PRWRU DEVRUSWLRQ ! $ IRU
second
[B]= stop the machine and check the
motor
The squeegee does not clean or
suction is ineffective the edge of the rubber blades in contact with the
ÀRRULVZRUQ
replace the rubber blade
the squeegee or hose is blocked or damaged unblock and repair the damage
WKHÀRDWVZLWFKKDVWULSSHGGLUW\ZDWHUWDQNLV
clogged by dirt or broken
empty the dirty water tank or reset the
ÀRDWVZLWFK
the suction hose is blocked unblock the hose
the suction hose is not connected to the squee-
gee or is damaged connect or repair the hose
there is no power to the suction motor or the
motor is faulty see: “The suction motor does not start”
The batteries do not provide the
normal work time (battery models
only) the battery poles and charging terminals are
dirty and oxidised clean and grease the poles and termi-
nals, charge the batteries
the electrolyte level is low top up all the elements with distilled wa-
ter as described in the instructions
the battery charger does not work or is unsu-
itable see battery charger instructions
there are considerable differences in density
between the various elements of the battery replace the damaged battery
The battery discharges too fast
during use, even though it has
been charged correctly and when
tested with a hydrometer at the end
of recharging, it turned out to be
uniformly charged (battery models
only) the battery is new and does not deliver 100% of
its expected capacity the battery must be “run-in” by perfor-
ming 20-30 charges and discharges to
obtain maximum performance
the machine is being used at maximum capacity
for continuous periods and the working time is
QRWVXI¿FLHQW
if possible, use batteries with a higher
capacity or replace the batteries with
others charged previously
the electrolyte has evaporated and does not co-
ver the plates completely top up all elements with distilled water
until the plates are covered then charge
the battery
The battery discharges too fast
during use, recharging with an
electronic battery charger is too
fast and after recharging the bat-
tery supplies the right voltage
(about 2.14V for each element
without load), but when tested with
a hydrometer is found not to be
uniformly charged (battery models
only)
WKHEDWWHU\VXSSOLHG¿OOHGZLWKDFLGE\WKH0D
-
nufacturer has been stored for too long before
EHLQJFKDUJHGDQGXVHGIRUWKH¿UVWWLPH
if recharging with a normal battery char-
ger is not effective, you must use a dou-
ble recharging cycle:
- charge it slowly over a 10 hour period
at a current of 1/10 the nominal capacity
for 5 hours (e.g. for a 100Ah(5) battery
the current must be set at 10A, using a
manual battery charger);
- rest for one hour;
- charge it with the normal battery char-
ger.
At the end of charging with the
electronic battery charger, the bat-
tery does not provide the correct
voltage (about 2.14 V per element
without load) and appears to be
uniformly not charged when tested
with a hydrometer (battery models
only) The battery has not been connected to the
battery charger (for example, because the low
voltage connector of the battery charger has
been erroneously connected to the machine
connector) connect the battery charger to the bat-
tery connector
the battery charger and power socket to which
the battery is connected are not compatible check that the power supply characteri-
stics indicated on the battery charger ra-
ting plate comply with those of the mains
power supply
the battery charger has not been installed cor-
rectly taking the actual voltage available at
the socket into account, make sure that
the connections of the primary of the
transformer inside the battery charger
are correct (consult the battery charger
manual)
the battery charger is not working make sure there is voltage to the batte-
ry charger, that the fuses are not blown
and that the current reaches the battery;
WU\FKDUJLQJZLWKDQRWKHUUHFWL¿HU,IWKH
battery charger is not working, contact
the technical service centre and indicate
the serial number of the battery charger
34