background image

  Hydra eSATA                                                                                                                 Appendix 

3  Appendix 

3.1  Precautions 

3.1.1  Power on/off precautions 

It is highly recommended to switch the unit off when not in use. When re-locating the device or 
when not in use for an extended period of time, we strongly recommend unplugging the unit. 
 

3.1.2  Location and placing precautions 

Avoid positioning your device in the following places: 

  Locations with direct sunlight, next to radiators, other sources of heat. 

  Locations with very high temperatures (more than 38° C) or humidity (more than 90%). 

  Very dusty or sandy locations. 

  Locations subject to vibration, shock, or with a sloping base. 

 

3.1.3  Electricity and power plug 

Careful attention must be paid to the following points in order to prevent damage, fire, and/or injury: 

  When removing the power cable from the socket, pull on the plug fixture and never on the cord. 

  Do not connect and remove the power cable with wet hands. 

  Keep the power cable away from heaters. 

  Never try to repair the power cable yourself or to modify it in any way. 

  If the unit is dropped or becomes damaged in any other way, unplug the power cable. 

 

3.1.4  Cables 

Use only the cables supplied or recommended by your vendor in order to avoid the risk of 
malfunction, electric shock, and/or possible interference to the device. 
 
 

3.2  FAQ 

Q: Why do I only see one volume in Non-RAID mode even though 4 drives are installed? 
A:

 To mount and access more than one volume, the eSATA host controller needs to support the 

Port Multiplier function. Without it, only one volume will be visible. 
 

Q: What file system should I choose to format my drive? 
A:

 This will depend on how you want to use the drive but in general, we recommend: 

 Windows 

XP/Vista 

Æ

 NTFS 

 Mac 

OS 

Æ

 HFS+ (Mac OS Extended) 

  To use it on both PC and Mac 

Æ

 FAT32 (single file size is limited to 4GB) 

 

Q: How many drives can fail before I loose my data? 
A:

 For RAID 0 and JBOD, any drive failure will result in the data being lost. For RAID 1, RAID 5 

and RAID 10, more than one drive failure at the same time will mean the data can not be 
recovered anymore. For Non-RAID, only the data on the defective drive will be lost. 
 
 

© Copyright 2009 by Macpower & Tytech Technology Co., Ltd. all Rights Reserved 

The information contained in this manual is believed to be accurate and reliable. Macpower & Tytech Technology 
assumes no responsibility for any errors contained in this manual. Macpower & Tytech Technology reserves the right to 
make changes in the specifications and/or design of this product without prior notice. The diagrams contained in this 
manual may also not fully represent the product that you are using and are there for illustration purposes only. Macpower 
& Tytech Technology assumes no responsibility for any differences between the product mentioned in this manual and 
the product you may have.

 

Page 7 

Содержание Hydra eSATA










Отзывы: