INVT HT 33010 Скачать руководство пользователя страница 6

Страница: 6 / 44

HT33 Series User Manual

Chapter 1 Quick Start

1.1 Introduction

This

chapter introduces the basic principles for UPS installation and debugging, so that customers

can install and debug UPS quickly.

1.2 Initial Checking

Perform the following checking operations prior to the UPS installation.

Visually examine if there is any damp, water, or damage inside and outside the UPS packing,

products and battery equipments due to the transportation. Report any such damage to the shipper

immediately.

Verify the product label and confirm the correctness of the equipment. The equipment label is

attached on the back of front door. The UPS model, capacity and main parameters are marked on

the label.

Verify correctness of the accessories. If there is any mistake for accessories, contact with shipper

or provider.

1.3 Environment Checking

Before installing UPS, please check these items as below:

1. Is the UPS operation environment temperature above 25

℃

If so, please add cooling equipments.

Note: Environment temperature above 20

℃

battery life will reduce to half when environment

rise each 10

℃

2. Is the UPS operation environment temperature below 0

℃

? If s

o, please add heaters.

3. Is the UPS operation environment humidity is above 90%? Is there any condensing? If so, please

add additional protection.

4. In the UPS operation environment, is there any sunshine shining in directly or life-form coming in? If

so, please add additional protection.

5. In the UPS operation environment, is there any dust, combustible or explosive gas? If so, please

add additional protection.

1.4 Installation Checking

After finishing installation, please check these items as below:

1. Is UPS installed on the flame-retardant materials?

2. Are all cables connected exactly?

3. Are all grounded system connected according to the manual?

4. Is there enough operation space around UPS?

5. Please confirm all UPS external terminals are fastened, the moment should meet requirements.

6. Please confirm that there are no screws, cables and other conductor left in the UPS. If there is,

please take out.

Содержание HT 33010













































Результаты поиска

Содержание HT 33010

Отзывы:

Похожие инструкции для HT 33010

Бренды по названию

Популярные бренды

INVT HT 33010, Руководство пользователя

Результаты поиска

Содержание HT 33010

Отзывы:

Похожие инструкции для HT 33010

Бренды по названию

Популярные бренды