Invertek Drives Eco Optidrive ODV-3-220043-1F12-SN страница 56 Скачать руководство пользователя

Страница: 56 / 77

| Optidrive Eco User Guide |

Version 3.05

www.invertekdrives.com

Par.

Parameter Name

Units

P0-36

DC Bus Voltage Log (256ms)

Diagnostic log for DC bus voltage. Values logged every 256mS with 8 samples total. Logging suspended on drive trip.

P0-37

DC Bus Voltage Ripple Log (20ms)

Diagnostic log for DC bus voltage ripple. Values logged every 20mS with 8 samples total. Logging suspended on drive trip.

P0-38

Heatsink Temperature Log (30s)

Diagnostic log for heatsink temperature. Values logged every 30S with 8 samples total. Logging suspended on drive trip.

P0-39

Internal Temperature Log (30s)

Diagnostic log for drive ambient temperature. Values logged every 30S with 8 samples total. Logging suspended on drive trip.

P0-40

Motor Current Log (256ms)

Diagnostic log for Motor Current. Values logged every 256mS with 8 samples total. Logging suspended on drive trip.

NOTE

The above parameters (P0-36 to P0-40) are used to store the history of various measured levels within the drive at various regular time

intervals prior to a trip. The values are frozen when a fault occurs and can be used for diagnostic purposes.

P0-41

Over Current Fault Counter

P0-42

Over Voltage Fault Counter

P0-43

Under Voltage Fault Counter

P0-44

Heatsink Over Temperature Fault Counter

P0-45

Reserved

P0-46

Ambient Over Temperature Fault Counter

NOTE

These parameters (P0-41 to P0-46) contain a record of how many times certain critical faults have occurred during a drives operating

lifetime. This provides useful diagnostic data.

P0-47

I/O Comms Fault Counter

Displays the number of communication errors detected by the I/O processor in messages received from the power stage processor

since the last power up.

P0-48

DSP Comms Fault Counter

Displays the number of communication errors detected by the Power Stage processor in messages received from the I/O processor

since the last power up.

P0-49

Modbus RTU / BACnet MSTP Fault Counter

This parameter is incremented every time an error occurs on the Modbus RTU communication link. This information can be used for

diagnostic purposes.

Extended P

arameters

Содержание Eco Optidrive ODV-3-220043-1F12-SN














































































Результаты поиска

Содержание Eco Optidrive ODV-3-220043-1F12-SN

Отзывы:

Похожие инструкции для Eco Optidrive ODV-3-220043-1F12-SN

Бренды по названию

Популярные бренды

Invertek Drives Eco Optidrive ODV-3-220043-1F12-SN, Руководство пользователя

Результаты поиска

Содержание Eco Optidrive ODV-3-220043-1F12-SN

Отзывы:

Похожие инструкции для Eco Optidrive ODV-3-220043-1F12-SN

Бренды по названию

Популярные бренды