background image

 
 

BALNAFETTACH HOUSE, PH26 3LW             (01479) 872 518                   [email protected]

 

 

 

 

6.

 

Make sure it is (good) finger-tight 

 as a loose heating coil can cause the MF3 to leak 

or display a heating coil error. 

 
7.

 

Re-fill the fluid tank and as with the first-time initial setup do allow the liquid to 
absorb for at least 30 minutes before using the MF3. 

 

NOTE:  

If during operation the MF3 

does not produce any smoke but you hear a ‘bubbling’ 

sound 

 STOP immediately as there is excessive fog liquid inside the heating coil.   

Try “flicking” the MF

3 away from you to expel the liquid from the barrel.  DO THIS OVER 

A SINK! 

  

 

 

 

.  Then try gently tapping the MF3 barrel on a flat surface to expel the liquid.  

If this does not work 

 you will need to change the heating coil. 

 

Troubleshooting 

No smoke is emitted even though the fan spins when you press the main button 

Ensure the heating coil is fully tightened. If the problem persists, 

carefully

 insert a fine 

screwdriver or other rod-like object into the barrel of the MicroFogger (the hole from which 
smoke is emitted) while the unit Rocker Switch is turned off.  

Briefly apply light pressure to the screwdriver, this will ensure that proper electrical contact 
is restored. Remove the screwdriver and try the unit again.  

Should this error persist, replace the coil with a new one. 

Fluid Tank Leaking 

Ensure both the heating coil and the tank are fully screwed home (finger tight).  If problem 
persists 

 ensure all white gaskets on the heating coil and the tank are properly and securely 

in place (and undamaged).

 

MicroFogger W

on’t 

Turn ON  

Plug it in to charge 

 remember use a mains fed USB charger outlet - (

with the 

Rocker/Toggle Switch 

‘ON’

) and wait at least 4 hours until the MicroFogger recharges. 

MicroFogger W

on’t 

Charge 

If the MF3 is in a critically low battery state, the battery state display may not show charged 
state for the first 30 minutes of charging.  If it still does not take/hold charge - please try 
using another charger and different micro-USB cable to diagnose whether it is an issue with 
the MF3 or not. 

 

 

Содержание MicroFogger 3 Pro














Отзывы: