Invenco 6002-0002-8801 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 47

background image

26

Document Number

DCV-00206

Date Released

Dec. 2016

Revision Number/Security level

R00 S2

Retrofit G7+InvencoLink Wayne Ovation (US) Installation Guide

Keypad

RFK Panel

(gasket part number MP0527):

1. Apply new gasket, starting with the horizontal segment along the top

edge of the bezel opening. Peel off the backing paper on this
segment only, align the gasket in the gasket channel and press into
place. Take care not to stretch the gasket.

2. Peel off the backing paper on the left vertical segment, align the

gasket in the channel and press into place. The top corner should
be closed and the edges touching.

3. Repeat step 2 with the other vertical channel.

4. Peel off the backing paper on the bottom horizontal segment, align

the gasket in the channel and press into place. The bottom-right
corner should be closed and the edges touching. The bottom-left
corner should be just touching the vertical segment as shown. A
small witness gap is permissible at this join.

Note: If you make a mistake with this gasket, it can be gently removed once. If you remove it more than
once the adhesive will fail and a replacement gasket will be needed.

4.2.2 Install the InvencoLink Converter

This Retro-Fit Kit does not include a communications method for the OPT. When this Retro-Fit Kit is being
installed on Side A (i.e. the first side) of the dispenser, a communications method MUST first be installed.

The approved communications methods are listed below.

UL Report Number

Kit Part Number

Retro-Fit Kit Description

MH61528

6009-0008-8801

InvencoLink DSP232

For Side B (i.e. the second side), you MUST have Side A (i.e. the first side) already installed, and you
may then proceed to §4.3 Installation Procedure.

For Side A (i.e. the first side), select the PSU Plate Assembly from this Retro-Fit Kit package and apply
the communications method selected from the table above, following the installation instructions supplied
with that Kit.
Once the communications method has been installed onto the PSU Plate Assembly, proceed to §4.3
Installation Procedure.

«
...
26
27
28
29
30
...
»

Содержание 6002-0002-8801
















































Отзывы:

Нет отзывов

Похожие инструкции для 6002-0002-8801

Бренд: Lucent Technologies Страницы: 93

PG-Flex FLL-712

Бренд: PairGain Страницы: 46

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 12

Бренд: Vivotech Страницы: 14

GuardScan Guard Tour GS1100 Series

Бренд: GIGA-TMS Страницы: 24

Бренд: Welcat Страницы: 144

Бренд: Eurotherm Страницы: 8

Бренд: Telic Страницы: 27

Бренд: e-Taxfree Nordic Oy Страницы: 14

Бренд: National Instruments Страницы: 8

Бренд: CAN Страницы: 19

Бренд: VendNet Страницы: 6

Бренд: NCR Страницы: 9

Бренд: ratiotec Страницы: 20

Бренд: IDTECH Страницы: 30

Бренд: Almex Страницы: 10

DNPOS70P-5BTH-N3700

Бренд: EBN Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды