Invenco 6001-0004-8801 Скачать руководство пользователя страница 46

Страница: 46 / 47

Document Number

DCV-00214

Date Released

Mar. 2017

Revision Number/Security level

R00 S2

Retrofit G6+InvencoLink GVR Encore 500S (US) Installation Guide

36. Reinstall the panel below the door and lock it.

d. Tilt the top of the panel outwards and insert its bottom lip first.
e. Bring the panel close to vertical, then lift it slightly to it slips over the upper hooks.
f.

The press the panel closed and allow it to drop a little into place.

Finally, lock the panel with the “GBCO” key.

37. The installation procedure is now complete.

4.3.1 Wiring Completion

Ensure that all cables are tidy and cannot become snagged or pinched when the door of the cabinet is
opened and closed.

WARNING

– Local regulations may also require that the installation is electrically tested and

certified BEFORE switch-on.

Insert bottom lip first

Tilt to vertical while

slightly raised

Hooks inside here

Last step: lock it

Содержание 6001-0004-8801
















































Результаты поиска

Содержание 6001-0004-8801

Отзывы:

Похожие инструкции для 6001-0004-8801

Бренды по названию

Популярные бренды

Invenco 6001-0004-8801, Руководство по установке

Результаты поиска

Содержание 6001-0004-8801

Отзывы:

Похожие инструкции для 6001-0004-8801

Бренды по названию

Популярные бренды