Invacare Harrier Plus Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 77

background image

36

7.5

Installing Or Adjusting Lateral Supports (where fitted)

INSTALLING:

1.

Remove the required existing pan head screws from each
backrest flange.

2.

Line up the support rail (A) with the holes in the backrest.

3.

With the longer screws provided attach the support rail to
the backrest flanges and into the screw inserts – DO NOT
screw into the backboard.

4.

Tighten securely, but do not over tighten.

ADJUSTING:

1.

Slide the lateral support into the support rail from the
bottom. Adjust to suit, and then firmly tighten the hand
wheel (B).

B

A

«
...
34
35
36
37
38
...
»

Содержание Harrier Plus














































































Отзывы:

Нет отзывов

Похожие инструкции для Harrier Plus

Бренд: Vicair Страницы: 18

Бренд: Gate Страницы: 20

Бренд: AAT Страницы: 84

Бренд: Otto Bock Страницы: 26

Бренд: CareCo Страницы: 10

Бренд: CareCo Страницы: 10

Бренд: Enigma Страницы: 5

Бренд: Enigma Страницы: 11

Бренд: E&J Страницы: 2

Бренд: panthera Страницы: 2

Бренд: Vermeiren Страницы: 176

Бренд: Mackworth Страницы: 28

Бренд: AAT Страницы: 40

Бренд: Livingston Innovations Страницы: 19

Бренд: Quantum Страницы: 3

Alante II GP202

Бренд: Golden Страницы: 40

Бренд: Motion Concepts Страницы: 8

Бренд: Motion Composites Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды