background image

 

14

 

 

3.3 

 

 

Safety Information On Electromagnetic Interference

 

This electric vehicle was successfully tested in accordance with international standards as to its compliance 
with Electromagnetic Interference (EMI) regulations. However, electromagnetic fields, such as those 
generated by radio and television transmitters, and cellular phones, can influence the functions of the electric 
vehicles.  Also, the electronics used in our vehicles can generate a low level of electromagnetic interference, 
which however will remain within the tolerances permitted by law. For these reasons we ask you to please 
observe the following precautions: 
 

 

WARNING: DANGER OF MALFUNCTION DUE TO ELECTROMAGNETIC INTERFERENCE! 

 

 

Do not switch on or operate portable transceivers or communication devices (such as radio transceivers 
or cellular telephones) when the vehicle is switched on! 

 

Avoid getting too close to strong radio and television transmitters! 

 

In case the vehicle should be set in motion unintentionally or the brakes are released, switch it off 
immediately! 

 

Adding electrical accessories and other components or modifying the vehicle in any way can make it 
susceptible to electromagnetic interference. Keep in mind that there is no sure way to determine the effect 
such modifications will have on the overall immunity of the electronic system!  

 

Report all occurrences of unintentional movement of the vehicle, or release of the electronic brakes to the 
manufacturer!  

Содержание Harrier Plus














































































Отзывы: