Invacare H335, Руководство пользователя

Страница: 5 / 44

R7766 – Armpad (Fig. 5)
Pos. Designation Quantity
A
Armpad, PUR
1
B
Glue 1
R7767 – Aesthetic cover (Fig. 6)
Pos. Designation Quantity
B
Plastic cover
1
C
Screw and nut 1
D
Protective cap 2
Warranty
We provide a manufacturer’s warranty for the product
in accordance with our General Terms and Conditions of
Business in the respective countries. Warranty claims can
only be made through the provider from whom the appliance
was obtained.
Compliance
Quality is of the utmost importance for our company; all
processes are based on the ISO 13485 standard.
This product features the CE mark, in compliance with the
Medical Device Directive 93/42/EEC Class 1.
Invacare is continuously working towards ensuring that the
company’s impact on the environment, locally and globally,
is reduced to a minimum. We only use REACH compliant
materials and components.
For further information please contact Invacare in your
country (for addresses, see back page of this manual).
Service life
The expected service life of this product is five years
when used daily in accordance with safety instructions and
intended use, stated in this manual. The effective service life
can vary according to frequency and intensity of use.
Safety
Safety information
WARNING!
Risk of falling!
– Do not use if defective.
– Do not use as sports equipment.
– Do not use as a climbing aid.
Labels and symbols on the product
Identification label (Fig. 8)
A
Manufacturer address
B
Conformity mark
C
Lot number
D
Maximum user weight
E
Read user manual
F Date of manufacture
G Product designation
Setup and usage
Installing the support folding handle
WARNING!
Risk of falling!
– Mount only to walls that have a sufficient
load-bearing capacity.
Defining the installation height (Fig. 1)
1. With the user standing upright, without shoes, measure
the height of the thumb’s upper joint. This height
corresponds to the support bar’s highest point
A
(middle
of support bar).
Installing the support bar (H335 / R7762) (Fig. 1)
1. Insert the 2° adjustment plate
D
.
2. Mark out the location of the holes on the wall (2 above
and 2 below outside) taking into account the previously
measured height.
3. Remove the 2° adjustment plate.
4. Position the wall attachment socket C for the support
bar accordingly.
5. Drill and insert 4 dowels appropriate for the type of wall.
6. Fix the socket to the wall using suitable screws, washers.
7. Snap the guard B onto the socket.
8. Insert the 2° adjustment plate from below again.
Adjusting the height
The support bar is supplied with a 2° adjustment
plate
D . To adjust the height of the support bar, use
option R7768 (3 adjustment plates of 0°, 2° and 4°).
1. Remove the 2° adjustment plate.
2. To lower by 10 mm, insert the 0° adjustment plate E .
3. To raise by 10 mm, insert the 4° adjustment plate F .
Installing the support leg (H345 / R7764) (Fig. 2)
1. Remove the socket’s guard, if fitted.
2. Remove the end cap C , if fitted or the cover on the
lower tube of the support bar D .
3. If not fitted, install the hinge piece B by sliding it onto
the lower tube. If necessary, use a plastic mallet. Fix
with one screw and cover with two protective caps.
4. Install the front end of the guide
J
into the oblong hole
in the support leg I using a plastic mallet and starlock
retainer ring
H
.
5. Remove the lower left-hand fixing screw G from the
socket
E
.
6. Position the guide J on the outside of the support bar,
the end with the wall hinge
F
pointing towards the
support wall or socket E .
7. Fasten the wall hinge F using the socket’s lower,
left-hand side fixing screw G .
8. Insert the upper end of the support leg I into the hinge
piece B . Fasten it using the screw and position two
protective caps K .
9. Install the socket’s guard.
10. Check that the whole assembly is firm and operates
correctly.
Adjusting the height (Fig. 2)
1. To decrease the height of the support leg turn the foot
assembly
L
counterclockwise into the support leg
I
.
2. To increase the height of the support leg turn the foot
assembly clockwise out of the support leg.
The height of the support bar can additionally be
adjusted with the 0°, 2° and 4° adjustment plates
like described above.
1572997-D 5