background image

299

A

S  AVE THESE INSTRUCTIONS

(299IO)  SPA (JET + BUBBLE)  ENGLISH  7.5” X 10.3”  PANTONE 295U  05/30/2018

English

Page 23

Spa Tub Drainage

1.

 

Turn off and unplug the spa control unit.

2.

 

Connect the drain valve adaptor to a garden hose and point the other end    

 

of the garden hose to a suitable draining area 

(see drawing 12)

.

3.

 

Remove the drain valve cap from outside of the spa tub and attach the 

 

drain valve adaptor to the drain valve 

(see drawing 12)

.

4.

 

From inside of the spa tub, open the drain valve cap, water will start 

 

fl owing out from the garden hose. 

5.

 

When the water stops draining, disconnect the spa control unit from  

 

 

the spa tub wall. Lift the spa tub wall from the side opposite the drain, 

 

leading any remaining water to the drain and emptying the spa completely    

 

(see drawing 13)

.

6.

 

Turn over the spa tub to empty any remaining water 

(see drawing 14)

.

7.

 

Unscrew the drain valve on the spa control unit side using a coin to drain 

 

out any water 

(see drawing 15)

.

8. 

Use a clean towel to wipe up any remaining water and moisture on the 

 

spa tub and spa control unit.

9.

 

Ensure the spa tub and spa control unit are thoroughly dried.

 

NOTE:

 The enclosed plugs 

(15 & 23) 

can be used to cover the water 

 

inlet and outlet connectors from the inside of the spa tub to prevent water 

 from 

fl owing out.

 

Spa Tub Cleaning

If dirt is visible in the water or water becomes cloudy and proper water 
chemistry does not clear it up, change the water and clean the spa tub.  
See “Spa Tub Drainage” section on how to drain the spa.
While empty, remove the cartridge housing from inside of the spa tub wall, 
clean and/or replace the fi lter cartridge. Use a sponge and mild soap solution 
to wipe away any soil or stains on the inside of the spa wall. Rinse thoroughly 
before refi lling with clean water.

IMPORTANT: 

Do not use steel wool, hard brushes or abrasive cleaners.

Biofi lm Removal

See your local spa professional for biofi lm removal products and advice.

Spa Tub Air Valve Fastening

Check the spa tub air valve for leakage and tightness before use. If air is leaking 
from the air valve, use the provided wrench 

(22) 

to tighten the air valve as follow:

1.

 

Make sure the spa tub is defl ated, open the air valve cap and insert the 
wrench 

(22)

 into the air valve body

 (see drawing 16)

.

2.

 

With one hand, hold the backside of the air valve base from the inside of the 
spa tub wall and turn the wrench

 (22) 

clockwise.

 IMPORTANT:

 Never adjust the air valve base when the spa is in use or 

fi lled with water. Only use the air valve wrench if the air valve is loose or 
there is leakage around air valve base. Do not over tighten the air valve: over tightening can damage the 
valve. Just ensure the air valve is snug and not leaking.

Spa Cover

Inspect the spa cover regularly for leaks, premature wear and tear, damage, or signs of deterioration. Never use 
a worn or damaged cover: it will not provide the level of protection required to prevent unsupervised access to the 
spa by a child.
Clean the cover inside and outside periodically using a sponge and a suitable solution that includes adequate 
disinfection (10 mg per liter of free chlorine). Do not use steel wool, hard brushes or abrasive cleaners.

MAINTENANCE (continued)

16

22

14

15

12

1

2

3

11

13

Содержание PureSpa SJB-HS-20-1C






























Отзывы: