background image

299

A

S  AVE THESE INSTRUCTIONS

(299IO)  SPA (JET + BUBBLE)  ENGLISH  7.5” X 10.3”  PANTONE 295U  05/30/2018

English

Page 4

c) The user should check the water temperature before entering the spa.
d) The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with 

the possibility of drowning.

e) Persons with any medical condition should seek medical advice before using a spa.
f) Persons using medication and/or having an adverse medical history should seek medical advice 

before using a spa since some medication may induce drowsiness while other medication may affect 
heart rate, blood pressure, and circulation.

g) Avoid putting the head underwater and swallowing spa water.
•  People with infectious diseases should not use a spa or hot tub.
•  To avoid injury exercise care when entering or existing the spa or hot tub.
•  Pregnant and possible pregnant women should consult a physician before using a spa or hot tub.
•  Water temperature in excess of 38°C degree may be injurious to your health.
•  Do not use a spa or hot tub immediately following strenuous exercise.
•  Prolonged immersion in a spa or hot tub may be injurious to your health.
•  When pregnant, soaking in hot water for long periods can harm your fetus. Measure the water 

temperature before entering. Do not enter spa if water is hotter than 38°C (100°F). Do not stay in spa 
for longer than 10 minutes.

•  Spa heat in conjunction with alcohol, drugs, or medication can cause unconsciousness.
•  Exit immediately if uncomfortable, dizzy, or sleepy. Spa heat can cause hyperthermia and 

unconsciousness.

•  The causes, symptoms, and effects of hyperthermia may be described as follows: Hyperthermia 

occurs when the internal temperature of the body reaches a level several degrees above the normal 
body temperature of 37°C (98.6°F). The symptoms of hyperthermia include an increase in the internal 
temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia 
include failure to perceive heat; failure to recognize the need to exit spa or hot tub; unawareness of 
impending hazard; fetal damage in pregnant women; physical inability to exit the spa or hot tub; and 
unconsciousness resulting in the danger of drowning.

•  The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia in hot tubs 

and spas.

•  Always add chemicals to water, never add water to chemicals. Adding water to chemicals may cause 

strong fumes or violent reactions and hazardous chemical spray.

•  Never jump or dive into a spa or any shallow body of water.
•  Assembly and disassembly by adults only.
•  This appliance can be used by children aged from 8 years and above and persons with reduced 

physical, sensory or mental capabilities or lack of experience and knowledge if they have been given 
supervision or instruction concerning use of the appliance in a safe way and understand the hazards 
involved. Children shall not play with the appliance. Cleaning and maintenance must be performed by 
an adult above 18 years old, and who is familiar with the risk of electric shock.

•  No part of the electrical appliance is to be located above the bath during use.
•  Keep the plug of this product more than 4m away from the spa and at a height of 1.2m at least.
•  Always unplug this product from the electrical outlet before removing, cleaning, servicing or making 

any adjustment to the product, and on raining days.

•  Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge 

trimmers and other equipment.

WARNING

Содержание PureSpa SJB-HS-20-1C






























Отзывы: