IntesisBox MH-RC-MBS-1 Скачать руководство пользователя страница 4

Страница: 4 / 23

MH-RC-MBS-1

User’s Manual r6.

3 EN

This information is subject to change without notice

IntesisBox

is a registered trademark of Intesis Software SLU

URL
Email
Phone

http://www.intesisbox.com
[email protected]
+34 938047134

4/23

Presentation

The MH-RC-MBS-1 interfaces allow a complete and natural

integration of

Mitsubishi Heavy Industries

air conditioners

into Modbus RTU (EIA-485) networks.

Reduced dimensions. 93 x 53 x 58 mm

3.7”

x 2.1” x 2.3”

Quick and easy installation.

Mountable on DIN rail, wall, or even inside the indoor unit of AC

•

External power not required.

•

Direct connection to Modbus RTU (EIA-485) networks. Up to 63 MH-RC-MBS-1 devices can
be connected in the same network.

MH-RC-MBS-1 is a Modbus slave device.

•

Direct connection to the AC indoor unit. Up to 16 AC indoor units can be connected to MH-
RC-MBS-1, controlling them as one (not individually).

•

Configuration from both on-board DIP-switches and Modbus RTU.

•

Total Control and Supervision.

•

Real states of the AC unit's internal variables.

•

Allows simultaneous use of the

AC’s

remote controls and Modbus RTU.

Up to 63 IntesisBox devices can be installed in the same Modbus RTU bus. However, depending on the configured speed, the

installation of Modbus Repeaters may be required

•

SCADA

•

PLC

•

DDC

•

BMS

•

HMI

•

Controller

•

etc

Up to 63
AC indoor
units*

Modbus RTU
EIA-485 network

Modbus RTU

Master

device

MH-RC-MBS-1

Содержание MH-RC-MBS-1
























Результаты поиска

Содержание MH-RC-MBS-1

Отзывы:

Похожие инструкции для MH-RC-MBS-1

Бренды по названию

Популярные бренды

IntesisBox MH-RC-MBS-1, Руководство пользователя

Результаты поиска

Содержание MH-RC-MBS-1

Отзывы:

Похожие инструкции для MH-RC-MBS-1

Бренды по названию

Популярные бренды