background image

  

MH-RC-MBS-1

 

User’s Manual r6.

3 EN

 

 

 

 

© Intesis Software S.L.U. - All rights reserved 

This information is subject to change without notice

 

 

IntesisBox

®

 

is a registered trademark of Intesis Software SLU

 

 

URL 
Email
Phone 

 

http://www.intesisbox.com                                          
info@intesisbox.com 
+34 938047134 

 5/23 

 

 

2.

 

Connection 

 
The interface comes with a plug-in terminal block of 2 poles to establish direct connection with 

the AC indoor unit. It comes as well with a plug-in terminal block of 2 poles to establish direct 
connection with the Modbus RTU EIA-485 network. 
 

2.1

 

Connect to the AC indoor unit 

 

The  MH-RC-MBS-1  connects  directly  to  the  Mitsubishi  Heavy  Industries  XY  Bus,  which  is  not 
provided within the interface. Depending on which controllers are available, the recommended 
connection

 methods are the following ones (details in Figure 2. 1): 

 

 

Wired remote controller available

. Connect the gateway as Slave in parallel with the 

wired remote controllers (Controller acts as Master).     
 

 

No  remote  controller  available

  Connect  the  gateway  directly  to  the  XY  bus  of  the 

indoor unit as Master when there is no Mitsubishi Heavy Industries Remote Controller. 

 
Maximum XY bus length is 600 m / 1,968.5 ft. The bus has no polarity sensitivity. 

 

Important:

 If a wired remote controller of the AC manufacturer is connected in the same bus, 

communication may shut down. 

 
 

 
 
 

 
 
 

 
 
 

 
 
 

 
 

 
 
 

 

 

 
 

 
 

 

 

 
 
 

 
 
 

 

IntesisBox

®

 

MH-RC-MBS-1 

MODBUS RTU 

EIA-485 

Bus

 

EIA485 

 A+  B- 

X Y 

AC Unit 

AC Indoor Unit 

Max. 600 m / 1,968.5 ft 

 

Connection to XY bus. 
Two wire cable. 

Y  

AC Indoor Unit 

IntesisBox

®

 

MH-RC-MBS-1 

MODBUS RTU 

EIA-485 

Bus

 

EIA485 

 A+  B- 

X Y 

AC Unit 

53 mm 

/ 2.1”

 

For wall mounting 

extract the upper 
and down staples 

until you hear the 
"click".

 

X Y 

MHI 

Max. 600 m / 1,968.5 ft 

Remote Controller 

Y  

 

 

90 mm 

/ 3.5”

 

 

Connection to XY bus. 

Two wire cable. 

53 mm / 

2.1”

 

90 mm / 3.5”

 

Figure 2. 1 

MH-RC-MBS-1 connection diagram

 

 

Internal 

electronic 
control 

board 

Internal 

electronic 

control 
board 

Содержание MH-RC-MBS-1
























Отзывы: