manualshive.com logo in svg

Intersil ISL8201M, Руководство пользователя, Страница: 5 / 9

Поделиться
Скачать
Intersil ISL8201M Скачать руководство пользователя страница 5

5

AN1386.1

D

ecember 23, 2009

NOTES:

1. R

1

 is used to set the output voltage of ISL820xMEVAL1Z. Initial setting is 6.49k

Ω

 for 1.5V output voltage.

2. R

2

 and R

3

, paralleling with R

1

, are used to adjust the output voltage of ISL820xMEVAL1Z.

3. R

4

 is used to set the overcurrent trip level of ISL820xMEVAL1Z. The ISL8201MEVAL1Z has integrated 3.57k

Ω, 

ISL8206MEVAL1Z has integrated 4.12k

Ω

, and 

ISL8204MEVAL1Z has integrated 2.87k

Ω

4. R

18

, C

18

 and C

19

 are the snubber network, which can reduce the stress for internal semiconductor.

5. R

13

, R

14

, C

12

, C

13

, C

14

 and C

15

 are the external compensation network. The ISL820xMEVAL1Z has integrated the type 3 compensation network inside the module 

for typical applications.

6. R

15

, R

16

, R

17

, R

20

, R

21

, C

17

, Q

2

 and Q

3

 are the power-up sequence circuit. In case of PVCC bias, power-up first, then input voltage. This circuit has to be implemented.

FIGURE 8. SCHEMATIC

Application Note 1386

Содержание ISL8201M










Отзывы:

Нет отзывов