manualshive.com logo in svg

Interlogix NX-595E, Руководство по установке

Поделиться
Скачать
Interlogix NX-595E Скачать руководство пользователя страница 28

 

28 

NX-595E Installation Manual 

Web Updates: 

When enabled, allows updating of the NX-595E Configuration 

Server's web pages via FTP. Normally disabled. 

Ping: 

The “ping” command is always functional whilst the NX-595E is in program 

mode and is defaulted to NOT operate whilst the NX-595E is in the normal run 
mode. Enable this option to allow the NX-595E to respond to "ping" commands in 
normal operation. For security reasons it is recommended this option remain 
disabled during normal operation.  

Web Time Updates: 

The NX-595E will check its internal and use the internet to 

compare it against GMT time. This is done every 15min and will update itself if 
the variance is greater than 3 minutes. 

NetworX Protocols: 

This protocol is disabled by default, but is active for the first 

5min after power up. Allows devices such as iPhones and UHS devices to 
communicate with the NX-595E via NetworX protocols.   

xConnect: 

This enables the app and automatic email configuration. Can only be 

disabled from a keypad. 

IP Address: 

An Internet Protocol (IP) address is a numerical label that is 

assigned to devices participating in a computer network. If DHCP is enabled and 
supported by your network, the NX-595E IP address will be automatically 
assigned, otherwise you will be required to enter your unique IP address here. 

Subnet Mask: 

Allows a network to be divided into subnets, and  allows the flow 

of network traffic between hosts to be segregated based on a network 
configuration. Applying the subnet mask to an IP address splits the address into 
two parts, an "extended network address" and a host address. A typical subnet 
mask is 255.255.255.0 

Primary DNS: 

IP address of the primary DNS server. DNS (Domain Name 

System) allows dedicated servers on the internet to be assign both an IP address 
and a corresponding name, called a domain name.  

Secondary DNS: 

IP address of the secondary DNS server. DNS (Domain Name 

System) allows dedicated servers on the internet to be assign both an IP address 
and a corresponding name, called a domain name.  

SSL Port: 

Selectable port configuration, a default port is 443. 

Web Access Passcode: 

This code allows the iPhone app to connect to this NX-

595E, it does not affect the operation of other features.  

xConnect Server 1: 

This server address should not be changed, it enables the 

remote web access, iPhone app and email services without having to set up port 
forwarding. 

xConnect Server 2: 

This server address should not be changed. 

Содержание NX-595E
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды