background image

 

6                                                                            IFS MCR200-1T-1TW User Guide 

 

Specifications Continued: 

 

Asymmetric Mode 

200m -> 100/55Mbps  
400m -> 90/50Mbps  
600m -> 70/40Mbps  
800m -> 60/25Mbps  
1000m -> 45/15Mbps 
1200m -> 35/10Mbps  
1400m -> 30/6Mbps  
1600m -> 25/4Mbps 

Symmetric Mode 

Performance* 
(Down Stream /  
Up Stream) 
 

200m -> 100/100Mbps  
400m -> 90/95Mbps  
600m -> 70/70Mbps  
800m -> 55/50Mbps  
1000m -> 45/35Mbps 
1200m -> 30/25Mbps  
1400m -> 25/20Mbps  
1600m -> 20/15Mbps 

Power 
Requirement 

5V DC, 2A 

Operating 
Temperature 

0~50ºC 

Storage 
Temperature 

-10~70ºC 

Operating 
Humidity 

10% to 90%, relative humidity, non-condensing 

Storage Humidity 

10% to 90%, relative humidity, non-condensing 

Standard Conformance 

Regulation 
Compliance 

FCC Part 15 Class A, CE 

Standards 
Compliance 

IEEE 802.3 10Base-T 
IEEE 802.3u 100Base-TX 
IEEE 802.3x Full Duplex Pause frame Flow Control 
ITU-T 

 

G.997.1 

 

G.993.1 VDSL 

 

G.993.2 VDSL2 (Profile 17a) 

 

* The actual data rate will vary on the quality of the copper wire and 
environment factors.

 

 
 
 

Содержание IFS MCR200-1T-1TW
























Отзывы: